How to Specify a Belt Dryer for Food Processing

How should you specify a belt dryer for food processing? State wet-feed rate, dried-product output and water evaporation, together with slice or particle size, bed depth, inlet and target moisture, and the temperature limit of the food. A band or mesh-belt dryer carries a layer of product through staged hot-air zones on a moving conveyor. It is a strong candidate for sliced, diced, flaked or fibrous foods — fruit, vegetables, herbs, spices, snack pellets and similar particulates — that need a long, gentle residence time and should not be tumbled. It is the wrong first choice for a pumpable puree or extract (evaluate a refractance window dryer or a spray dryer) and for a sticky filter cake that will not sit as a permeable bed.

This guide is for food-plant and dehydration-plant engineers writing a belt-dryer enquiry. Moisture is on a wet basis unless stated otherwise. The calculations are illustrative, not a quotation. They do not replace a trial on the actual cut size and pretreatment (blanching, sulphiting or osmosis, where used).

When is a belt or mesh-belt dryer the right family?

An industrial band dryer, also called a belt or conveyor dryer, feeds wet material evenly onto a moving belt or apron and passes it through one or more drying zones where temperature, airflow, humidity and belt speed can be set independently. A mesh-belt dryer uses a perforated stainless-steel mesh so that air can be driven through the bed rather than only across it. Genex Tech Industries LLP (GTI Group) describes both on its band dryer and mesh belt dryer pages, and lists typical food uses such as fruit slices and dices, onion and garlic flakes, ginger and turmeric, herbs, snack pellets and coconut chips. Related food-process pages are also published on foodtechprojects.com and under GTI’s vegetable dehydration and fruit drying systems.

GTI’s band-dryer page quotes a customised capacity range of 100 kg/h to 10 TPH. The page does not say whether those figures are wet feed, dried product or evaporation. Treat them as a span of project sizes, not as a rating you can copy into a purchase order. On this site the equipment family is also described on the belt dryer and mesh belt dryer service pages.

Feed form Evaluate first Usually not first
Slices, dices, flakes, herbs, pellets, fibrous pieces Band or mesh-belt dryer, often with a cooling zone Rotary drum (breakage and mixing); spray dryer (feed is not a liquid)
Free-flowing granules that can be fluidised Fluid-bed or vibratory fluid-bed dryer A long belt, unless a gentle finish or cooling belt is required
Spreadable puree or paste Refractance window or drum dryer A mesh belt, unless the puree has already been formed into a stable layer or slab
Pumpable extract or dilute slurry Spray dryer Belt dryer
Small specialty or trial lots Tray or heat-pump dryer A large continuous belt, unless the plant already has one

Which parameters belong in the enquiry?

  • Mass balance: wet-feed rate, dried-product rate, inlet and target moisture, and the test method. Seasonal peak moisture should be the design case.
  • Piece geometry: cut size and shape, because they set diffusion time and how uniformly air can pass through the bed.
  • Bed depth and belt loading: too deep a bed dries unevenly; too thin a bed wastes belt area.
  • Zone temperatures and humidity: a hot first zone can case-harden pieces; a cooler finishing zone evens out residual moisture. A final cooling zone helps packing.
  • Residence time and belt speed: speed is not a capacity rating by itself; it is the means of setting time at a given belt length.
  • Hygiene and utilities: product-contact material (typically SS304 or SS316 for food), cleanability, heating medium (steam, thermic fluid, gas or electric), and exhaust or heat recovery.

The Food and Agriculture Organization (FAO) published indicative moisture contents for some dehydrated vegetables in its fruit and vegetable processing manual (Table 9.4.4), including 4% for onion slices, 4% for garlic cloves, 5% for carrot strips and 6% for potato strips. Those figures are useful planning values. Your commercial specification may be different; many onion-dehydration contracts also set a maximum well below 8% for shelf life. Always write the limit you will pack to.

Worked example: 200 kg/h of dried onion slices

Suppose the packing rate is 200 kg/h of dried onion slices at 4% moisture, matching the FAO table value used here as an illustration. USDA FoodData Central lists raw onion at about 89% water. If the slices enter the dryer at that moisture, dry solids in the product are 200 × 0.96 = 192 kg/h. The wet feed is then 192 / (1 − 0.89) = 1,745 kg/h, and evaporation is 1,545 kg/h.

Item Value Notes
Dried product 200 kg/h at 4% moisture Packing-basis capacity
Assumed feed moisture 89% wet basis Raw-onion water content; confirm after peeling and slicing
Wet feed 1,745 kg/h Almost nine kilograms of slices per kilogram of packed product
Water evaporated 1,545 kg/h This, not the 200 kg/h, sizes heaters and exhaust
Approximate latent heat 1,050 kW At 2,450 kJ/kg
Indicative thermal input 1,930–2,580 kW At 4,500–6,000 kJ/kg, until an air-flow balance is done

If incoming slices were somehow at 85% moisture instead of 89%, the same 200 kg/h at 4% would need only 1,280 kg/h of wet feed and 1,080 kg/h of evaporation — about 30% less water. That is why an enquiry that says “a 200 kg/h onion dryer” without inlet moisture cannot be compared with another offer. Electrical demand for fans, belt drives and any dehumidification should be stated separately from the thermal figure.

Belt area follows from loading and residence time, not from a catalogue length alone. As an illustration only, a 2 m-wide belt loaded at 6 kg of wet slices per square metre, travelling at 12 m/h, carries 144 kg/h of wet feed and would need a much larger area, or a deeper loading and a longer residence time, to approach the 1,745 kg/h of this example. Those geometry numbers are not a GTI standard model; they show why loading, speed and evaporation have to be calculated together, then checked on a trial.

Common specification mistakes to avoid

  • Buying on “200 kg/h” or “2 TPH” without stating wet feed, dried product or evaporation, and without inlet moisture.
  • Using the 100 kg/h–10 TPH range on a supplier page as if it were a guaranteed rating for your food.
  • Setting a single high temperature for the whole dryer and then blaming the machine for case-hardening or colour loss.
  • Loading the belt too deep in order to “get more capacity” from a short dryer.
  • Omitting cooling, hygiene design and packing-room humidity — dried vegetables pick up moisture after the dryer.
  • Mixing heater or steam kilowatts with fan and drive power in one installed-kW figure.

Frequently asked questions

Is a mesh-belt dryer different from a band dryer?

They are the same family. “Mesh belt” emphasises through-flow of air via a perforated belt; “band” or “apron” may use a different conveyor construction. For slices and flakes, through-flow is usually desirable. Ask the supplier to describe belt type, airflow direction and zone arrangement, not only the name.

Can one belt dryer handle several vegetables?

Often yes, if each product has its own recipe for loading, zone temperatures and belt speed, and if cleaning between allergens or strongly flavoured products (onion, garlic, chilli) is realistic. Size the dryer for the governing evaporation duty, which is not always the product with the highest packed output.

Do I need a trial?

Yes, for a new cut size, a high-sugar fruit, or a colour-sensitive leaf. Pretreatment and seasonal raw-material moisture change the drying curve as much as the machine does.

Where can I read GTI’s belt-dryer pages?

See the band dryer and mesh belt dryer product pages, the mesh-belt page on foodtechprojects.com, and this site’s belt dryer service page.

About Genex Tech Industries LLP (GTI Group)

Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray dryers, band and belt dryers, rotary drum dryers, flash dryers, fluidised-bed and vibratory fluid-bed dryers, paddle dryers, vacuum dryers, heat pump dryers and refractance window dryers, as published on gtidryers.com. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See also the drying machines section of this site and GTI’s food ingredient dryers page.

Sources and authorship

  • FAO, Fruit and Vegetable Processing, Chapter 9, Table 9.4.4, “Moisture and shipping factors for some dehydrated vegetables” (fao.org).
  • USDA FoodData Central, raw onion water content (approximately 89 g/100 g) (fdc.nal.usda.gov).
  • Published band-dryer, mesh-belt and food-drying pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com, foodtechprojects.com, and the drying-machine pages on epcprojects.in.

The worked example is an illustrative calculation from the stated assumptions, not a plant measurement or a performance guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named process engineer, and no individual is cited as having approved the technical content. Please treat it as a specification aid pending engineering review of any project-specific design.

Next step

If you are specifying a belt dryer for food processing, email mktg@gtidryers.com or use the contact page on this site. Send the product and cut size, wet-feed rate, inlet and target moisture, required dried output at peak season, temperature or colour limits, heating medium, hygiene requirements and the installation location. Related guides cover refractance window dryers for purees, industrial tea dryers and how to choose the right industrial dryer.