How should a buyer specify dust explosion protection for a spray, flash or fluid-bed dryer? Start with test data for your powder, not with a catalogue of vents and suppressors. Get the dust tested (explosibility, KSt, Pmax, minimum ignition energy and ignition temperatures), carry out a dust hazard analysis covering the dryer and the cyclone, bag filter, conveying and packing room, and then choose a combination of prevention (temperature control, deposit control, inerting where needed) and protection (venting, suppression, isolation). A dryer that is safe on its own can still be part of an unsafe plant if the downstream equipment is ignored.
This checklist is for process, safety and project engineers buying or upgrading dryers for food powders, pharmaceutical excipients, chemicals, starch, biomass and other combustible solids. It is engineering guidance, not a substitute for a site-specific hazard study by a competent person.
What has changed recently?
- Standards. NFPA states that, as of 2025, the consolidated NFPA 660, Standard for Combustible Dusts and Particulate Solids, combines the former NFPA 652 with NFPA 61, 484, 654, 655 and 664 (NFPA, 21 May 2026). Explosion venting remains in NFPA 68 and prevention and protection systems (isolation, suppression, inerting) in NFPA 69. Specifications that still cite only NFPA 652 or 654 should be updated.
- India: the Sigachi Industries blast, 30 June 2025. The explosion at the microcrystalline cellulose (MCC) plant in Pashamylaram, Telangana, killed 54 people, as reported. In August 2025 the Telangana government told the High Court that a dust explosion was the likely cause; a Factories Department inspection report listed violations including failure to provide an adequately sized explosion relief panel and temperature alarms on the spray dryer, and failure to carry out a dust hazard analysis before using the spray dryer and other powder equipment (Indian Express, 30 August 2025). The technical expert committee’s report, as described by The Hindu on 21 November 2025, traced the source to a bag-sealing machine in a confined, congested packing area with MCC dust present, not to the spray dryer. The report had not been made public at that time. The two accounts differ on the ignition point; both point to dust hazard analysis, explosion relief, housekeeping, training and dust control across the whole powder area.
- United States, 12 February 2026. An explosion and fire occurred at a custom spray-drying facility in Burlington Township, New Jersey; all twelve employees were accounted for and the cause was under investigation, according to CBS Philadelphia, 13 February 2026. No cause should be inferred.
Where do ignition sources arise in each dryer type?
| Dryer | Typical ignition or fuel concern | Prevention focus |
|---|---|---|
| Spray dryer | Deposits near the hot-air disperser or on walls that self-heat; burning lumps falling into the cone; fines in cyclone and bag filter | Outlet and inlet temperature limits, deposit inspection and cleaning, nozzle or atomiser condition, CO or temperature-rise detection |
| Flash / spin-flash dryer | Hot gas meeting fine, dry product; friction sparks in mills or fans; product build-up in ducts | Feed consistency, duct design without dead zones, foreign-body removal, spark detection |
| Fluid-bed / vibratory fluid-bed | Fines carried to the filter; electrostatic charge on dry powders; hot spots under poor fluidisation | Bonding and earthing, fluidisation control, filter design |
| Rotary dryer (biomass) | Glowing particles from the furnace; smouldering deposits; sparks in the discharge | Spark detection and extinguishing, furnace controls, discharge isolation |
| Packing and bagging | Dust clouds in confined rooms; electrical equipment; heat from sealing | Dust extraction, classified electrical equipment, housekeeping, layout |
What test data should you have before design?
| Property | What it tells you | Used for |
|---|---|---|
| Explosibility screening | Whether the dust can explode at all | Whether further protection is needed |
| KSt (bar·m/s) and Pmax (bar) | Rate of pressure rise and maximum pressure | Vent and suppression sizing; vessel strength |
| Minimum ignition energy (MIE) | Sensitivity to sparks and static | Earthing, bonding, conveying design |
| Minimum ignition temperature, cloud and 5 mm layer | Hot-surface and deposit limits | Surface-temperature limits, inlet temperature |
| Limiting oxygen concentration (LOC) | Oxygen level below which ignition is not possible | Inerting design, closed-loop nitrogen systems |
| Self-heating behaviour | Whether deposits or bulk product can ignite over time | Residence-time and storage limits |
Test the product as it leaves the dryer and the fines in the filter, which are finer and usually more sensitive. Formulation changes (sugars, fats, carriers, solvents) mean new tests.
Worked example: a hot-surface screening limit
A common screening rule for equipment surfaces in combustible dust areas, used in IEC 60079-14 for electrical equipment, is to take the lower of two limits: two-thirds of the cloud minimum ignition temperature, and the 5 mm layer ignition temperature minus 75 K. Assume an illustrative powder with a cloud ignition temperature of 420 °C and a 5 mm layer ignition temperature of 260 °C:
- Cloud limit: 2/3 × 420 = 280 °C
- Layer limit: 260 − 75 = 185 °C
- Screening surface limit: 185 °C
If that dryer uses inlet air at about 200 °C, as was reported for the Sigachi spray dryer, surfaces around the air inlet can sit above the screening limit. That is not automatically unsafe; dryer chambers are assessed differently, and thicker deposits ignite at lower temperatures than a 5 mm layer. It is a signal to examine deposit formation and cleaning, temperature-rise detection, whether a lower inlet temperature is feasible, and whether venting or suppression is needed. Drying-specific guidance, such as VDI 2263 Part 7 (spray-drying installations) and Part 5 (fluidised-bed dryers), and NFPA 660 give the full method.
Buyer’s checklist for a new or upgraded dryer
- Dust test report for product and filter fines, plus any solvent data.
- Dust hazard analysis covering dryer, cyclone, bag filter, ducts, mills, conveying, silos and packing.
- Hazardous-area classification for dust (and vapour if solvents are present), with equipment selected to suit.
- Defined operating envelope: maximum inlet and outlet temperatures, interlocks and alarms on high temperature and loss of feed.
- Deposit control: inspection access, cleaning procedure and frequency, and design that avoids ledges and dead zones.
- Protection basis: vent area and discharge direction (NFPA 68), or suppression, with isolation of connected equipment (NFPA 69). Vents must not discharge into occupied areas.
- Inerting for solvent-wet feeds or very sensitive powders, with oxygen monitoring.
- Earthing and bonding of all conductive parts; antistatic filter media where needed.
- Housekeeping limits for packing and process rooms, and dust extraction at transfer points.
- Training, permits for hot work, and management of change when capacity or product changes.
The last point matters. Sigachi’s expert report, as reported, linked the accident to a rise in output after new equipment was commissioned, with untrained staff and deferred maintenance. Treat a capacity increase as a change that reopens the hazard study.
Frequently asked questions
Is an explosion vent enough?
Not by itself. A vent limits pressure in the vessel it protects. It does not stop flame travelling to the filter or upstream ducts, and it needs a safe discharge area. Isolation and prevention measures are usually needed alongside.
Do food powders really explode?
Many do. Sugar, starch, milk powder, flour and many plant extracts are combustible dusts. Test rather than assume.
When is a closed-loop nitrogen spray dryer needed?
Typically when the feed contains flammable solvent or the powder is unusually sensitive. Aqueous feeds of most food powders run in air with other safeguards. See how to size a spray dryer and the pharmaceutical dryer guide.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray dryers, flash dryers, fluidised-bed and vibratory fluid-bed dryers, rotary drum dryers, band and belt dryers, paddle dryers, vacuum dryers, heat pump dryers and refractance window dryers, as published on gtidryers.com. GTI’s spray and flash dryer pages list explosion-safe design options for solvent-based products and fine powders; the specific protection must still follow the dust data and hazard study for each project. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See also this site’s spray dryer page.
Sources and authorship
- NFPA, “Combustible Dust Explained”, 21 May 2026; NFPA 660, NFPA 68 and NFPA 69 standard pages.
- The Indian Express, “‘Dust explosion’: Telangana govt informs high court what likely caused Sigachi factory blast”, 30 August 2025.
- The Hindu, “Sigachi report: Production enhancement without trained staff and safety measures led to the explosion”, 21 November 2025.
- CBS Philadelphia, “12 employees evacuated after possible explosion, fire at New Jersey manufacturing building”, 13 February 2026.
- IEC 60079-14 (surface-temperature rule for dust layers and clouds); VDI 2263 Part 5 (explosion protection in fluidised-bed dryers) and Part 7 (dust fire and explosion protection in spray-drying and integrated equipment).
- Published dryer pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com.
The worked example uses illustrative values, not test data for any product. Incident summaries are as reported by the cited media; official findings may differ. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named process-safety engineer, and no individual is cited as having approved the technical content.
Next step
To discuss a new dryer or a safety-driven upgrade, email mktg@gtidryers.com or use the contact page. Send the product, feed form and solvent (if any), dust test data if available, capacity, current inlet and outlet temperatures, the downstream equipment and the installation location.
