Which dryer belongs on a resin line, and which belongs on a PVC or chlor-alkali-related solids duty? Decide from the size of the evaporation load and the moisture problem you actually have. Hygroscopic resin pellets, powders and granules often need only a small mass of water removed, but they need it removed evenly and held below a tight residual-moisture specification before compounding or moulding. Suspension PVC leaving a centrifuge is a different problem: published process descriptions typically start from a wet cake of around 20–30% moisture and dry it to a few tenths of a percent, which is a large evaporation duty, often in a flash dryer followed by a fluid bed. Chlor-alkali plants themselves produce chlorine, caustic soda and hydrogen; many of the drying questions around that chain are about downstream solids such as PVC resin, salt, or other inorganic cakes — not about “drying caustic” in the same sense as drying a polymer pellet.
This guide is for resin producers, PVC and polymer plants, and engineers working on chemical complexes that include chlor-alkali or vinyl units. It compares dryer families, works two illustrative mass and heat balances side by side, and flags corrosion and safety issues that should appear in an enquiry. It is engineering guidance, not a quotation or a performance guarantee. Genex Tech Industries LLP (GTI Group) publishes resin, polymer and chemical drying pages; it does not, at the time of writing, publish a dedicated chlor-alkali or PVC-plant capacity page, so no GTI project, capacity or client figure for those units is used here. Moisture is on a wet basis unless stated otherwise.
Why one dryer family rarely covers a resin plant and a PVC cake duty
Two duties are easy to confuse because both may be described as “drying polymer”:
- Residual-moisture control of an already-formed resin or plastic granule, often after storage or conveying, where the water mass to be removed is small but the specification is tight and re-absorption after the dryer matters.
- Process drying of a wet cake or slurry, where most of the water is still in the feed and the evaporation rate dominates air flow, heater size and operating cost.
GTI’s resin drying systems and polymer drying systems pages, and its longer article on polymer, resin and plastic dryers, discuss synthetic and polymer resins (including epoxy, polyester, phenolic and acrylic types), resin powders and granules, and the use of fluid-bed, vacuum-tray, paddle, spray and rotary-vacuum dryers according to feed form. The polymer article also notes PVC granules as a material whose surface or process moisture may be removed in a heated-air or other suitable thermal dryer. Those pages are about matching the dryer to the moisture problem; they are not evidence of a particular PVC or chlor-alkali installation.
Which dryer should you evaluate for resins?
| Resin feed and duty | Families to evaluate | Why | Cautions |
|---|---|---|---|
| Granules, pellets or free-flowing resin powder with surface or moderately bound moisture | Fluid-bed or vibratory fluid-bed dryer; in some low-moisture plastic-processing duties, a dry-air or desiccant-style system is also used in the industry | Uniform gas–solid contact and, if specified, a cooling zone before packing or conveying | The feed must fluidise; very low residual-moisture targets may be limited by inlet-air humidity as much as by heater size |
| Heat-sensitive or solvent-wet specialty resins and intermediates | Vacuum tray or rotary-vacuum dryer | Lower boiling temperature and a closed path for solvent recovery | Cycle time, condenser utilities and discharge containment must be in the scope |
| Resin filter cakes, pastes or slurry-based resins | Paddle dryer or rotary-vacuum dryer; spin-flash or flash dryer if the cake can be dispersed | Contact heat and agitation, or mechanical dispersion, without first turning a cake into a dilute slurry | Sticky phases, shear and residual solvent all need a trial or a clear test plan |
| Resin emulsions or liquid polymer solutions that must become a powder | Spray dryer, open or closed-loop | Direct liquid-to-powder conversion | Evaporation follows feed solids; see how to size a spray dryer. Solvent-based systems need a formal hazard assessment. |
Hygroscopic resins can re-absorb moisture after a correctly sized dryer if cooling, conveying and packaging are left out of the design. A residual-moisture reading at the dryer discharge is not the same as the moisture in the bag or silo several hours later. Measure both when the specification is tight.
What drying duties appear around chlor-alkali and PVC?
A chlor-alkali unit electrolyses brine to produce chlorine, caustic soda (sodium hydroxide) and hydrogen. Drying questions attached to that chain are usually about solids and polymers, not about the cell room itself:
- Salt (the brine feedstock, and sometimes a dried salt product) may need residual-moisture control after crystallisation or centrifugation. GTI publishes salt-drying material separately; that is a solids-drying problem, typically for free-flowing crystals.
- Caustic soda is commonly concentrated as a liquor and then solidified by flaking or prilling. That is an evaporation and forming duty, not the same as a convective cake dryer. Do not specify a flash or rotary dryer for “caustic drying” by analogy with a polymer cake unless the actual feed form supports it.
- PVC is a major downstream use of chlorine, via ethylene dichloride and vinyl chloride monomer (VCM). After VCM recovery, suspension-PVC slurry is typically centrifuged to a wet cake and then dried.
- Other chlorinated intermediates and inorganic cakes may appear on the same complex; each still needs its own feed-form and corrosion assessment.
Published descriptions of suspension-PVC drying are consistent on the shape of the duty, even though plants differ in equipment detail. A 2015 study of PVC porous grains in Colloids and Surfaces A reports that the powder is dried to a suitable moisture, described there as less than 0.3 wt%, and that centrifuge cakes in the work were about 70–80 wt% solids (that is, about 20–30% moisture). The same paper describes industrial flash drying in hot air, quoted there at 160 °C, down to about 1 wt% moisture, followed by fluid-bed drying before storage, and notes that dehydration is a substantial part of the process energy. A Chemical Engineering technology profile of suspension PVC describes a flash dryer with a cyclone dryer finishing the powder to about 0.2–0.3 wt% moisture. A Powder Technology study of an industrial S-PVC line reports a centrifuge cake at 23% moisture and a final moisture of 0.2%, and discusses both contact fluid-bed drying and two-stage flash-plus-fluid-bed systems.
Those figures are literature, not GTI measurements and not a template to copy uncritically. Temperature limits matter because PVC can degrade if it is overheated; residual VCM is a separate process-safety and product-quality issue that is normally addressed in degassing before the dryer, and must not be treated as a casual dryer add-on. Emulsion or paste-grade PVC, where it is produced as a latex, is a different feed and is often evaluated for spray drying rather than cake drying.
For short-residence cake drying versus longer-residence drums, see rotary drum dryer versus flash dryer. A rotary dryer may still be evaluated for some bulk inorganic solids on a chlor-alkali or vinyl complex, but it is not automatically the right machine for fine PVC powder or for a tight-spec resin pellet.
Worked examples: a tight-spec resin versus a PVC wet cake
Both examples are illustrative calculations with stated assumptions. They are not plant measurements, not GTI performance data, and not recommended operating specifications.
Example A — hygroscopic resin granules
Assume 1,000 kg/h of resin granules enter a dryer at 0.25% moisture and must leave at 0.02% moisture.
- Dry solids = 1,000 × (1 − 0.0025) = 997.5 kg/h.
- Dried-product output = 997.5 ÷ (1 − 0.0002) = 997.7 kg/h.
- Water evaporated = 1,000 − 997.7 = 2.3 kg H2O/h.
The evaporation mass is small. The latent-heat load at 2,256 kJ/kg is only about 1.4 kW. Even at 4,500–6,000 kJ/kg of water the thermal figure attributed to evaporation is only about 3–4 kW. That does not mean the dryer is a 4 kW machine. Heating the resin itself can dominate. If the granules are raised from 25 °C to 80 °C and a specific heat of 1.5 kJ/kg·K is assumed (polymer values vary; this is an illustration only), the sensible-heat load is 1,000 × 1.5 × 55 ÷ 3,600 ≈ 23 kW — several times the latent load. Inlet-air humidity, residence time and cooling after the dryer will often set the air flow, not the 2.3 kg/h of water. Electrical power for fans or a dry-air system is a separate figure.
Example B — suspension-PVC cake, using literature-range moistures
Assume 2,000 kg/h of centrifuge cake at 25% moisture, dried to 0.3% moisture. Those moisture values sit inside the published ranges cited above; they are assumptions for the arithmetic, not a design standard.
- Dry solids = 2,000 × (1 − 0.25) = 1,500 kg/h.
- Dried-product output = 1,500 ÷ (1 − 0.003) = 1,505 kg/h.
- Water evaporated = 2,000 − 1,505 = 495 kg H2O/h.
Using the same 4,500–6,000 kJ/kg specific-energy brackets as elsewhere in this series, the thermal input is about 619–826 kW. The latent-heat-only figure is about 311 kW. Sensible heating of the PVC is present too, but it is small compared with this evaporation load — the opposite of Example A.
| Cake moisture (wet basis) | Dried product at 0.3% (kg/h) | Water evaporated (kg/h) | Thermal input at 4,500 kJ/kg (kW) | Thermal input at 6,000 kJ/kg (kW) |
|---|---|---|---|---|
| 20% | 1,605 | 395 | 494 | 659 |
| 25% (worked case) | 1,505 | 495 | 619 | 826 |
| 30% | 1,404 | 596 | 745 | 993 |
All three rows start from the same 2,000 kg/h of wet cake. A better centrifuge that delivers 20% instead of 30% moisture cuts the evaporation load, and the heat load, by about a third in this table. That is why dryer sizing and upstream dewatering have to be discussed together. If a flash stage removes most of the water and a fluid bed finishes the last one percent or so, split the evaporation duty between the stages rather than sizing both machines on the full 495 kg/h.
The contrast with Example A is the point of the two calculations. A 1,000 kg/h resin dryer and a 2,000 kg/h PVC-cake dryer are not “similar polymer dryers” with different nameplates. One is a low-evaporation, specification-and-humidity problem; the other is a large evaporation problem with a short-residence first stage and a temperature limit.
Corrosion, residual monomer and dust safety
Chlorides, wet chlorine traces, acidic liquors and caustic spills drive materials of construction on a vinyl or chlor-alkali complex. A stainless grade that is acceptable for a clean resin pellet dryer may not be acceptable for a salt cake or a chloride-wet intermediate. State the chemical environment in the enquiry; do not leave it to a generic “chemical duty” specification.
PVC dust can be a combustible-dust issue, and organic resin powders often are. Residual VCM is toxic and flammable and is normally stripped before drying; any discussion of residual monomer belongs in the process-safety file, not in a casual list of dryer options. Combustible-dust references include NFPA 652 and NFPA 654, consolidated in 2025 into NFPA 660, Standard for Combustible Dusts and Particulate Solids. Equipment for potentially explosive atmospheres in the EU is covered by Directive 2014/34/EU (ATEX). Citing these documents does not mean that any particular dryer, plant or project complies with them.
Common specification mistakes to avoid
- Using one “polymer dryer” specification for tight-spec resin pellets and for a PVC or inorganic wet cake.
- Sizing a PVC dryer without stating cake moisture from the actual centrifuge, or without splitting evaporation between a flash stage and a finishing stage.
- Treating caustic concentration and flaking as if it were the same operation as drying resin granules.
- Ignoring air humidity and post-dryer re-absorption on hygroscopic resins.
- Mixing thermal heater duty with fan or desiccant-system electrical power in one kilowatt number.
- Leaving residual-monomer, chloride-corrosion and combustible-dust assessments out of the scope.
Frequently asked questions
What dryer is commonly described for suspension PVC?
Published process descriptions most often describe centrifuge dewatering followed by a flash (pneumatic) stage and a finishing dryer, frequently a fluid bed or a cyclone dryer, to a residual moisture of a few tenths of a percent. Emulsion or paste PVC is a different feed and may be evaluated for spray drying. Confirm the polymerisation route before shortlisting equipment.
Can a fluid-bed dryer be used for both resin granules and PVC powder?
A fluid bed can be a candidate in both cases when the particles actually fluidise, but the evaporation load, temperature limit, residence time and corrosion environment can still be very different. Shared hardware should be a deliberate decision, not an assumption.
Does GTI publish a standard PVC or chlor-alkali dryer capacity?
Not on a dedicated PVC or chlor-alkali page that we could verify. GTI does publish resin, polymer, chemical, salt and dryer-family pages, and it custom-engineers capacity around the stated feed. Ask for a balance on your wet-feed rate, moisture basis and residual-moisture target rather than a catalogue nameplate.
Why is my resin dryer “too big” for the water it removes?
Because at very low inlet moisture the machine may be sized on heating the solid, on residence time, and on the dryness of the inlet air, not on evaporation kilograms alone. The worked resin example above shows how the sensible-heat load can exceed the latent-heat load.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray dryers, band and belt dryers, rotary drum dryers, flash dryers, fluidised-bed and vibratory fluid-bed dryers, paddle dryers, vacuum dryers, heat pump dryers and refractance window dryers, as published on gtidryers.com. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See also the drying machines section of this site and GTI’s chemical drying systems page.
Sources and authorship
- “Dehydration and drying poly(vinyl)chloride (PVC) porous grains: 1. Centrifugation and drying in controlled humid atmospheres”, Colloids and Surfaces A, 2015, ScienceDirect record.
- “Technology Profile: Suspension Polymerization of Polyvinyl Chloride”, Chemical Engineering, chemengonline.com.
- “Experimental and numerical study of the effects of pre-drying of S-PVC using a pneumatic dryer”, Powder Technology, 2018, ScienceDirect record.
- Sobulska, M.; Wawrzyniak, P.; Woo, M.W. “Superheated Steam Spray Drying as an Energy-Saving Drying Technique: A Review”, Energies 2022, 15(22), 8546.
- NFPA 652; NFPA 654; and NFPA 660 (2025), Standard for Combustible Dusts and Particulate Solids (National Fire Protection Association).
- Directive 2014/34/EU (ATEX) on equipment and protective systems intended for use in potentially explosive atmospheres.
- Published product and application pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com, including the resin, polymer, chemical, spray, flash, paddle, vibratory fluid-bed and about pages cited above, and the drying-machine pages on epcprojects.in.
The worked examples are illustrative calculations from the stated assumptions, not plant measurements or performance guarantees. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named process engineer, and no individual is cited as having approved the technical content. Please treat it as a specification aid pending engineering review of any project-specific design.
Next step
If you are specifying a dryer for a resin, PVC or related chemical solid, email mktg@gtidryers.com or use the contact page on this site. Send the polymer or chemical identity, feed form, wet-feed rate, inlet and target moisture with the measurement basis, maximum product temperature, any residual-solvent or residual-monomer constraint, utilities, corrosion environment and installation location. Related guides on this site cover pigment dryers, dyes and dye intermediates, specialty and fine chemicals, and how to choose the right industrial dryer.
