Why does fruit or herbal-extract powder stick to the spray dryer wall, and how do you stop it? Sugar-rich feeds contain low-molecular-weight sugars and acids with a low glass transition temperature (Tg). If the particle surface is warmer than about its Tg while it is still moist, the particle turns soft and tacky, and it sticks to the chamber wall, the cone and the cyclone instead of leaving as powder. The fixes fall into two groups: change the formulation (carriers or proteins that raise Tg), or change the process (cooler, drier air near the wall and outlet, and cooling the powder quickly). Most plants need a balance of both, set by trials on their own feed.
This guide is for process engineers and plant managers producing fruit, vegetable, herbal-extract and other sugar-rich powders. Moisture is on a wet basis unless stated otherwise.
What does the recent research say?
- A review by Samborska and co-authors in Drying Technology (published 6 July 2023) states that spray drying of sugar-rich foods suffers mainly from low glass transition temperature, which shows up as high stickiness and lower drying efficiency and yield. It reports that carriers remain the most popular remedy, that proteins can act as anti-stickiness agents, that sugar content can be reduced by membrane techniques, and that dehumidified air has been verified as a way to lower drying temperature and so reduce the carrier needed.
- A review of berry powders in Applied Sciences (Preciado Ocampo et al., published 12 December 2025) notes that reported Tg values for the same sugar vary with purity, residual water and test method; it cites values of 32.2 °C for glucose and 14 °C for fructose from one study, and 100–243 °C for maltodextrin depending on its dextrose equivalent (DE).
- An earlier review by Sobulska and Zbiciński (Drying Technology, 2021, doi:10.1080/07373937.2020.1832513) covers carbohydrate carriers, prebiotic fibres and proteins, and reports that fibres and proteins may give high yields at lower carrier levels than conventional carriers.
The practical message: fruit sugars on their own have Tg values near or below room temperature once they hold some water, while a carrier such as maltodextrin is far higher. Mixing them lifts the Tg of the particle, and keeping the particle drier and cooler keeps it below that Tg.
Where in the dryer does stickiness show up?
| Where deposits form | What it usually means | First things to check |
|---|---|---|
| Near the atomiser or roof | Wet droplets hitting the wall before a dry skin forms | Atomiser speed or nozzle pattern, spray angle, feed rate against chamber size |
| Lower chamber wall and cone | Particles dry enough to move but hot and above their Tg | Outlet temperature, outlet air humidity, carrier level, wall temperature |
| Cyclone, ducts, bag filter | Fine particles still warm and tacky in the exhaust | Outlet temperature, duct insulation and cold spots that condense moisture |
| Bags or silos after packing (caking) | Powder picks up moisture or is packed warm | Powder cooling, packing-room humidity, packaging barrier |
How much carrier do you need, and what does it cost you?
Carrier level is usually set by trials, and published levels vary widely with the fruit, the carrier and the dryer. The worked example below shows how to see the consequences of whatever level the trials point to. All values are assumptions for illustration.
Basis: 1,000 kg/h of fruit juice concentrate at 20% soluble solids. Carrier (maltodextrin) at 40% of total powder solids. Powder at 4% moisture.
| Item | Calculation | Result |
|---|---|---|
| Fruit solids | 1,000 × 0.20 | 200 kg/h |
| Carrier needed | 200 × 0.40 ÷ 0.60 | 133.3 kg/h |
| Total feed | 1,000 + 133.3 | 1,133.3 kg/h at 29.4% solids |
| Powder at 4% moisture | 333.3 ÷ 0.96 | 347.2 kg/h |
| Water to evaporate | 1,133.3 − 347.2 | 786.1 kg/h |
| Fruit solids in the powder (as sold) | 200 ÷ 347.2 | 57.6% |
If trials with dehumidified inlet air or a protein carrier allowed the carrier to drop to 25% of solids, the carrier would fall to 66.7 kg/h, the powder to 277.8 kg/h, and the fruit content of the powder would rise to 72.0%. The water to evaporate barely changes (1,066.7 − 277.8 = 788.9 kg/h), so dryer size is set by the juice, not the carrier. What changes is carrier cost, label claims and product value. This is why the process options below are worth evaluating before simply adding more carrier.
Which process changes reduce stickiness?
- Control the outlet temperature tightly. The outlet air temperature is the best everyday indicator of the temperature of the finished particles. Too high and particles stay hot and tacky; too low and they stay wet. Find the window in trials and hold it with feed-rate control.
- Use drier inlet air. Dehumidified air lets the dryer reach the same powder moisture at a lower temperature, which the Samborska review reports as a verified way to reduce stickiness and carrier demand. It matters most in humid seasons and climates.
- Cool the wall and the cone. Cool-air jacketing or sweeping of the lower chamber and cone keeps the surfaces that particles touch below their sticky temperature.
- Remove and cool the powder quickly. Pneumatic conveying with cool, dry air or an after-cooler fluid bed brings the powder below its Tg before it is packed.
- Check the atomisation. Too coarse a spray leaves wet droplets that reach the wall; too fine a spray sends more powder to the cyclone. Match droplet size to the chamber.
- Prepare the feed. Uniform solids, full dissolution of the carrier and removal of fibres or seeds that block nozzles all help.
For the mass and heat balance behind chamber size and air flow, see our guide on how to size a spray dryer. For very heat-sensitive purées where spray drying struggles, see when to use a refractance window dryer.
A simple trial plan
- Fix the feed solids and atomisation, then run a series of outlet temperatures at one carrier level. Record yield (powder collected ÷ solids fed), wall deposits and powder moisture.
- Repeat at two or three carrier levels, or with an alternative carrier such as a protein or fibre.
- If available, repeat the best two settings with dehumidified inlet air.
- Measure powder moisture, water activity and, where possible, Tg by DSC (differential scanning calorimetry) for the best samples.
- Store samples at the packing-room humidity for a few days and check caking.
Frequently asked questions
Why does my powder look fine in the chamber but cake in the bag?
It was probably packed warm or picked up moisture after the dryer. Absorbed water lowers Tg, so a powder that was glassy at the outlet can turn sticky at room temperature. Cool the powder, control packing-room humidity and use a good moisture barrier.
Is maltodextrin the only option?
No. Gum arabic, proteins such as whey protein, and dietary fibres have all been studied. The choice affects cost, labelling, taste and solubility, so test the options on your product.
Can I spray dry a juice without any carrier?
For most sugar-rich juices it is difficult in a conventional dryer. Lower-temperature drying with dehumidified air, sugar reduction or a different drying method may reduce or avoid the need. Trials will tell.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray, fluid bed, refractance window and band dryers, as listed on its spray dryer and products pages. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See GTI’s herbal extract drying and fruit drying pages, the spray dryer page on foodtechprojects.com, and this site’s spray dryer page.
Sources and authorship
- Samborska K. et al., “Recent progress in the stickiness reduction of sugar-rich foods during spray drying”, Drying Technology, 2023, 41(16), 2566–2585.
- Preciado Ocampo V. et al., “Effect of Drying Methods on the Physical and Surface Properties of Blueberry and Strawberry Fruit Powders: A Review”, Applied Sciences, 2025, 15(24), 13094.
- Sobulska M., Zbiciński I., “Advances in spray drying of sugar-rich products”, Drying Technology, 2021, 39(12), 1774–1799.
- Published spray, herbal-extract and fruit drying pages of Genex Tech Industries LLP (GTI Group).
The worked example is an illustrative calculation from stated assumptions, not a plant measurement or guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named engineer, and no individual is cited as having approved the technical content.
Next step
Fighting wall deposits or low powder yield? Email mktg@gtidryers.com or use the contact page. Send the product, feed solids and sugar profile if known, carrier and level used now, required powder moisture, output per hour, your present dryer and its problems, and the installation location.
