Which industrial dryer should a pigment plant use? Choose it from the feed form and the powder properties you must protect, not from the pigment’s name alone. A pumpable slurry or dispersion can often be spray-dried to a powder. A wet filter cake or paste from a filter press or centrifuge is usually a better fit for a spin-flash or flash dryer, because the machine can disperse the cake while it dries. Free-flowing particles or a powder that only needs finishing and cooling may suit a fluid-bed or vibratory fluid-bed dryer. Organic pigments, inorganic pigments, titanium dioxide (TiO2) and iron oxides often need different temperature limits, materials of construction and dust-safety measures, even when their moisture numbers look similar.
This guide is for pigment manufacturers and project engineers at the specification or enquiry stage. It sets out a feed-form selection framework, a worked mass and heat balance that compares drying a filter cake directly with re-slurrying it for spray drying, and the safety and quality checks that should sit in the enquiry. It is engineering guidance, not a quotation or a performance guarantee. Final design needs product data and, for many pigments, a trial. All moisture figures in this article are on a wet basis (mass of water divided by the total mass of the wet material) unless another basis is stated.
What should you fix before you choose a pigment dryer?
Three different numbers are often called “capacity”. They are not interchangeable:
| Term | Definition | Typical unit | What it drives |
|---|---|---|---|
| Wet-feed rate | Cake, slurry or powder entering the dryer | kg/h | Feeder, atomiser or disperser, upstream filter or mill |
| Dried-product output | Powder leaving the collector at the specified residual moisture | kg/h | Packing, conveying, sales volume |
| Evaporation rate | Wet-feed rate minus dried-product output (for a water-only system with no other losses) | kg H2O/h | Air flow, heater duty, chamber or duct size, fans and exhaust |
Always ask which basis a quoted capacity uses. Genex Tech Industries LLP (GTI Group) states on its spray dryer page a published range “from a few kg/hr to 50+ tons/hr evaporation”. Evaporation and powder output only become comparable once feed solids and final moisture are fixed. GTI’s flash dryer page lists capacity as customised to the product in its technical specification table; treat any capacity figure without a stated basis as incomplete.
Before shortlisting a technology, write down:
- The exact pigment (for example, an organic azo pigment, a coated TiO2 grade, or a yellow iron oxide) and its physical form at the dryer inlet: pumpable slurry, cohesive filter cake, paste, granules or powder.
- Inlet moisture or feed solids, and the required residual moisture, both on a stated basis, plus the test method. For many pigments, matter volatile at 105 °C is determined by methods such as ISO 787-2; use the method in the buyer’s specification.
- Maximum product temperature, and any limit on shade, tinting strength, oil absorption, particle-size distribution, bulk density or dispersibility.
- Whether residual solvent, not only water, is present.
- Corrosion, abrasion and contamination constraints, and the available heating medium (steam, thermic fluid, fuel-fired hot air, or electricity). Keep thermal energy (heater or steam duty) separate from electrical demand (fans, atomiser, vibrators, feeders).
- Site utilities, hours of operation, and whether the dust is combustible or the feed contains a flammable solvent.
How should feed form steer the dryer choice?
GTI’s pigment and dye application guidance starts from the same question: can the feed be pumped and atomised, must a cake be dispersed as it dries, or is the solid already particulate? That is a more reliable starting point than the product name. The table below is a screening guide, not a final specification.
| Feed form | Dryer families to evaluate | Typical reason | Main cautions |
|---|---|---|---|
| Pumpable slurry, suspension or solution | Spray dryer, sometimes with an integrated or downstream fluid bed | Converts liquid directly to powder; particle size is influenced by atomisation and drying history | Evaporation load is set by feed solids; abrasive slurries wear nozzles or wheels; some organics are heat- or oxidation-sensitive |
| Wet filter cake or paste from a filter or centrifuge | Spin-flash or flash dryer; paddle or rotary-vacuum dryers where residence time, solvent recovery or a closed system is required | Mechanical dispersion can dry a cake without first turning it back into a dilute slurry | Sticky intermediate-moisture phases may need back-mixing or a different feeder; attrition can change particle size |
| Free-flowing particles, granules or conditioned powder | Fluid-bed or vibratory fluid-bed dryer (VFBD) | Uniform gas–solid contact for residual moisture and, if specified, cooling in a second zone | The feed must actually fluidise; wet or cohesive cakes will channel or agglomerate |
| Primary drying plus finishing | Spray or spin-flash dryer followed by a fluid bed | Most of the water is removed quickly; final moisture and powder cooling are finished at a lower temperature | Two air systems, fines return and a clear split of evaporation duty between stages |
GTI publishes application pages for pigment drying systems and a longer selection article on spray, spin-flash and fluid-bed systems for pigments and dye intermediates. Those pages list spray, fluid-bed, paddle, vacuum-tray and rotary-vacuum options, and they note that pigment feeds commonly arrive with substantial moisture after precipitation, filtration or washing. Use them as product context, not as a substitute for a mass balance on your own feed.
How do TiO2, iron oxide and organic pigments differ in the dryer?
| Pigment family | What usually matters in the dryer | Practical implication |
|---|---|---|
| Titanium dioxide (TiO2) | Particle size, surface treatment and residual moisture after wet milling, dewatering or filtration. Flash, spin-flash and spray drying are all used in industry, depending on the process route. | Do not copy inlet temperature or residual-moisture targets from another TiO2 plant. Confirm whether the grade is treated, and whether the dryer must preserve a specified particle-size or oil-absorption range. |
| Iron oxide pigments | Oxidation state and shade can be temperature-sensitive, especially for yellows and some reds. The solids are inorganic, but cakes can still be cohesive and abrasive. | Set a maximum product temperature from the grade, not from a generic “inorganic pigment” limit. Check abrasion on the disperser, ducting and collectors. |
| Other inorganic pigments | Corrosion (acids, chlorides, sulphates), abrasion and, for some precipitated pigments, a sticky cake. | Materials of construction and feeder design often decide reliability as much as heat transfer does. |
| Organic pigments | Shade, crystal form and thermal or oxidative stability. Many organic pigment dusts are combustible. Residual solvent may be present from synthesis or washing. | Lower temperature limits, inert or closed-loop operation if solvent is present, and a dust-hazard assessment are often part of the scope, not add-ons. |
Two pigments with the same inlet moisture can still need different dryers. A cohesive organic-pigment cake and a pumpable inorganic dispersion are different feeding problems. A TiO2 cake that must keep a narrow particle-size range is a different quality problem from an iron oxide that must not shift shade. GTI’s published guidance makes the same point: selection should be product-specific.
Worked example: what does it cost, in evaporation, to re-slurry a pigment cake?
The calculation below is an illustrative example with stated assumptions. It is not a measurement from a Genex Tech Industries LLP (GTI Group) installation, and it is not a performance guarantee.
A plant receives 800 kg/h of inorganic pigment filter cake at 45% moisture (wet basis) and must deliver powder at 0.5% moisture (wet basis).
Step 1: Solids, product and evaporation if the cake is dried directly
- Dry solids in the cake = 800 × (1 − 0.45) = 440 kg/h. Solids are assumed conserved; dust losses and any other volatiles are ignored here.
- Dried-product output = 440 ÷ (1 − 0.005) = 442 kg/h.
- Water evaporation rate = 800 − 442 = 358 kg H2O/h.
That evaporation rate — not the 800 kg/h wet-feed figure, and not the 442 kg/h of powder — is what sizes the air system and the heater if this cake is fed to a spin-flash, flash or other direct cake dryer.
Step 2: The same solids, re-slurried to 30% solids for spray drying
If the cake is diluted back to a pumpable slurry at 30% total solids (70% moisture) and then spray-dried to the same 0.5% powder moisture:
- Wet-feed rate to the atomiser = 440 ÷ 0.30 = 1,467 kg/h.
- Powder output is still 442 kg/h.
- Water evaporation rate = 1,467 − 442 = 1,024 kg H2O/h.
Re-slurrying multiplies the evaporation load by about 2.9 times in this example. The extra water is water you already removed in the filter and then put back.
Step 3: Thermal energy, kept separate from fan power
A 2022 review in Energies gives a broad industrial range of about 4,000–6,000 kJ per kg of water for conventional hot-air drying, and higher values for some spray dryers, against a latent heat of roughly 2,250 kJ/kg at 100 °C. Using 4,500 and 6,000 kJ/kg as bracketing assumptions for specific thermal energy:
| Route | Wet feed (kg/h) | Powder at 0.5% (kg/h) | Water evaporated (kg/h) | Thermal input at 4,500 kJ/kg water (kW) | Thermal input at 6,000 kJ/kg water (kW) |
|---|---|---|---|---|---|
| Cake dried directly | 800 | 442 | 358 | 447 | 596 |
| Cake re-slurried to 30% solids, then spray-dried | 1,467 | 442 | 1,024 | 1,281 | 1,707 |
These kW figures are thermal duties. They do not include electrical power for fans, an atomiser, a disperser rotor, vibrators or auxiliaries. A spray-dryer trial may still be the right process choice if the required particle size, bulk density or dispersibility can only be obtained by atomisation. The calculation shows the energy and evaporator-size penalty of that choice when a filter cake is already available.
Step 4: A simple air-flow check for the cake-drying route
Assume, for illustration only, inlet air at 200 °C, outlet air at 90 °C, and that the useful air-temperature drop supplies the latent heat of the water at 2,450 kJ/kg (an allowance above 2,250 kJ/kg for heating the liquid). With a dry-air specific heat of 1.01 kJ/kg·K:
- Useful heat = 358 × 2,450 ÷ 3,600 ≈ 244 kW.
- Air mass flow ≈ 244 × 3,600 ÷ (1.01 × 110) ≈ 7,900 kg/h.
This air-flow estimate is idealised. It ignores heat losses, leakage, moisture already in the inlet air, and any bound-moisture zone where the product temperature rises and the driving force falls. It is a starting check, not a heater-sizing sheet. Humid ambient air and a high exhaust dew point can force a larger flow; that is one reason to size on the most humid design season, not on an annual average. For a fuller spray-dryer air and dew-point procedure, see our guide on how to size a spray dryer.
When is a trial necessary, and what should you not copy from another plant?
A laboratory or pilot trial is strongly advisable when the pigment is new to the supplier, the cake is cohesive or passes through a sticky moisture range, the shade or particle-size specification is tight, residual solvent is present, or you are choosing between re-slurrying and direct cake drying. A trial is the right place to confirm feedability, wall deposits, attrition, residual moisture, shade and the workable inlet and outlet temperature window.
Do not treat another plant’s inlet temperature, residence time or residual-moisture target as transferable. TiO2 surface treatments, iron-oxide shade limits and organic-pigment crystal forms are grade-specific. GTI lists process evaluation among its industrial-dryer services; ask what sample mass and analytical data a trial requires.
What dust and solvent safety issues should the specification include?
Many organic pigments and some pigment preparations are combustible dusts. Uncoated TiO2 and iron oxides are inorganic oxides and are not themselves fuels, but organic surface treatments, residual solvents, additives or blended preparations can change the dust-hazard picture. A dust-hazard analysis should be done on the actual powder, including fines from milling and collector hoppers.
Recognised references include NFPA 652 (fundamentals of combustible dust) and NFPA 654 (combustible particulate solids). In 2025 those documents were consolidated into NFPA 660, Standard for Combustible Dusts and Particulate Solids. In the European Union, equipment intended for use in potentially explosive atmospheres is covered by Directive 2014/34/EU (ATEX). Mentioning a standard or directive here does not mean that any particular dryer, plant or project complies with it. Local regulations and a site-specific assessment govern what must be installed.
If the feed contains a flammable solvent, evaluate closed-loop or inert-gas drying, solvent recovery, leak tightness and explosion protection as part of the process design, not as a later accessory. Collector design (cyclone, bag filter, and any wet scrubber or other exhaust treatment) should be sized for the actual particle-size and powder-loading, because pigment fines are both a product-recovery and a hygiene-and-safety issue.
Common specification mistakes to avoid
- Comparing a powder-output rating from one supplier with an evaporation rating from another.
- Choosing a spray dryer for a filter cake without calculating the extra evaporation created by re-slurrying.
- Selecting a fluid-bed dryer for a cake that will not fluidise until it is already almost dry.
- Copying TiO2 or iron-oxide temperature set-points onto an organic pigment, or the other way around.
- Quoting a single “kW” figure that mixes burner or steam duty with fan and motor power.
- Leaving dust collection, powder cooling, milling, shade testing and materials of construction out of the scope comparison.
- Ignoring combustible-dust or solvent hazards because the product is “only a pigment”.
Frequently asked questions
Can one dryer handle both organic and inorganic pigments?
Only if each pigment has been assessed. Shared hardware can be practicable when feeds, temperature limits, cleaning, corrosion and dust-safety requirements are compatible. It is not automatic. Colour change-over and cross-contamination often matter as much as heat transfer.
Is a spray dryer the default choice for TiO2?
No. Industry practice includes flash, spin-flash and spray drying, depending on whether the feed is a cake or a slurry and on the required pigment properties. The process route and a trial, where needed, should decide, not the product name.
When should a spin-flash dryer be evaluated instead of a spray dryer?
When the plant already has a wet cake or paste that can be metered and dispersed, and when you want to avoid putting water back into a filter cake. A spray dryer remains a candidate when a pumpable slurry is the natural feed and the powder structure depends on atomisation. GTI’s article on when to use a spin-flash dryer sets out this distinction.
What residual moisture should a pigment powder reach?
The buyer’s or in-house specification governs, together with the agreed test method (for example, matter volatile at 105 °C). There is no single industry number that fits TiO2, iron oxides and organic pigments alike. Over-drying can waste energy and, for some organics, harm shade or flow.
Do GTI pigment dryers have a published standard capacity?
GTI describes pigment dryers as custom-engineered around the material, moisture and capacity. Where a numeric range is published for a dryer family, confirm whether it is wet feed, dried product or evaporation, and do not apply a food- or coconut-application figure to a pigment duty.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray dryers, band and belt dryers, rotary drum dryers, flash dryers, fluidised-bed and vibratory fluid-bed dryers, paddle dryers, vacuum dryers, heat pump dryers and refractance window dryers, as published on gtidryers.com. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See also the drying machines section of this site and GTI’s chemical drying systems page.
Sources and authorship
- ISO 787-2, General methods of test for pigments and extenders — Part 2: Determination of matter volatile at 105 °C (International Organization for Standardization).
- Sobulska, M.; Wawrzyniak, P.; Woo, M.W. “Superheated Steam Spray Drying as an Energy-Saving Drying Technique: A Review”, Energies 2022, 15(22), 8546.
- NFPA 652, Standard on the Fundamentals of Combustible Dust; NFPA 654, Standard for the Prevention of Fire and Dust Explosions from the Manufacturing, Processing, and Handling of Combustible Particulate Solids; and NFPA 660, Standard for Combustible Dusts and Particulate Solids (2025), which consolidates those documents (National Fire Protection Association).
- Directive 2014/34/EU of the European Parliament and of the Council (ATEX), on equipment and protective systems intended for use in potentially explosive atmospheres.
- Published product and application pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com, including the pigment, spray dryer, flash dryer, spin-flash, vibratory fluid-bed and chemical-drying pages cited above, and the drying-machine pages on epcprojects.in.
The worked example is an illustrative calculation from the stated assumptions, not a plant measurement or a performance guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named process engineer, and no individual is cited as having approved the technical content. Please treat it as a specification aid pending engineering review of any project-specific design.
Next step
If you are specifying a pigment drying line, email mktg@gtidryers.com or use the contact page on this site. Send the pigment type, feed form, wet-feed rate, inlet and target moisture with the measurement basis, required powder properties, maximum product temperature, available heating medium and utilities, installation location, and any solvent or combustible-dust information you already have. That is enough to start an evaporation-based comparison of cake drying versus slurry drying and to decide whether a trial is needed. For the wider choice between dryer families, see how to choose the right industrial dryer and the comparison of a rotary drum dryer versus a flash dryer. Related guides on this site cover dyes and dye intermediates, specialty and fine chemicals, and resins, PVC and chlor-alkali chemicals.
