How to Dry Digestate and LFOM from a CBG Plant

How should you dry digestate and liquid fermented organic manure (LFOM) from a compressed biogas (CBG) plant? Dewater or concentrate first, then dry only the remaining water that mechanical separation cannot remove. Raw or poorly dewatered digestate is mostly water; putting the whole stream through a thermal dryer wastes fuel and oversizes the exhaust system. Sticky, pasty cakes often suit an indirect paddle dryer, especially where odour and exhaust volume must be kept down. Fibrous cakes can go to a band or conveyor dryer. Once the solids are free-flowing, a vibratory or combination fluid-bed stage can finish moisture and produce a handleable granule. LFOM, which is a liquid, should be concentrated in an evaporator before any solid drying or granulation step.

This guide is for CBG, biogas and organic-fertiliser plant managers who need a stable, transportable product from anaerobic-digestion residue. Moisture is on a wet basis unless stated otherwise. The worked numbers are illustrative. They are not a performance guarantee, and they are not a claim that a dried product automatically meets any fertiliser regulation.

What are you actually trying to produce?

In a typical biogas or CBG flowsheet, digestate leaves the digester very wet. Genex Tech Industries LLP (GTI Group) states on its digestate drying page that the by-product often contains 80–90% water, and that after mechanical dewatering, thermal drying is used to reach a stable 10–20% moisture. That 10–20% target is a storage and handling range, not automatically a legal grade.

If the product will be sold in India as fermented organic manure, the Fertiliser (Inorganic, Organic or Mixed) (Control) Order matters. The Fertiliser (Control) (Third) Amendment Order, 2025, notified as S.O. 1477(E) on 27 March 2025, sets moisture for fermented organic manure (FOM) at 30–70% by weight and for LFOM at 90–97% by weight, together with organic-carbon, pH, conductivity, pathogen and heavy-metal limits. A cake dried to 10–20% moisture may be a useful, lower-volume organic fertiliser or granule, but it can fall below the FOM moisture window. Agree the intended FCO grade — FOM, LFOM, phosphate-rich organic manure (PROM), or another scheduled product — before you fix the dryer endpoint. GTI discusses LFOM and PROM concentration and drying separately on its LFOM and PROM page, including falling-film and multi-effect evaporators for the liquid fraction.

Which dryer family matches the cake or liquid?

Feed Families to evaluate first Why Watch-outs
Sticky or pasty dewatered cake; odour-sensitive site Indirect hollow paddle dryer Heat is transferred through the paddles and jacket, so exhaust air volume is much smaller than in a convective dryer Needs a condenser or scrubber for the vapour; sticky phases can coat heating surfaces if residence time and wall temperature are wrong
Fibrous or high-viscosity cake that can be spread Multi-stage band / conveyor dryer Gentle, continuous drying with zoned temperature and a long residence time Bed depth and feeding uniformity control the result; a soup-like slurry will leak or smear on a belt
Conditioned, free-flowing granules Vibratory fluid-bed or combination fluid-bed dryer Good finishing and cooling once the material can be fluidised Not a first-stage dryer for a wet, plastic cake
Coarse, variable agricultural or municipal solids Rotary drum dryer Robust, high-throughput handling of mixed particle sizes Higher exhaust volume and tighter fire and odour controls are often required
LFOM or liquid digestate at 90–97% water Falling-film, multi-effect or vacuum evaporator, then a dryer only for the concentrate or solids Evaporators are built to remove bulk water from liquids; a dryer is not a cheap evaporator Vacuum or multiple effects reduce steam use; nutrient and microbial limits still have to be checked against the intended grade

GTI also notes that dryers can be integrated with waste heat from engine jacket water, exhaust flue gas, low-pressure steam or a biomass hot-air generator. Waste-heat integration can cut purchased fuel, but only if the heat is available at a useful temperature when the dryer is running, and only after the evaporation load has been calculated honestly. GTI publishes a custom capacity span from 500 kg/h pilot plants to 20+ TPH industrial complexes on the digestate page; that page does not state whether those figures are wet feed, dried product or evaporation, so they should not be used as a design rating.

Worked example: why dewatering changes the dryer size

Consider a required output of about 294 kg/h of dried solids at 15% moisture (250 kg/h of bone-dry solids). Two feed cases, both ending at 15% moisture, show the cost of skipping mechanical dewatering. Dry solids are assumed to be conserved.

Case (illustrative) Feed moisture Wet feed, kg/h Dried product, kg/h Evaporation, kg/h Mass reduction Approx. latent heat at 2,450 kJ/kg, kW Indicative thermal input at 4,500–6,000 kJ/kg, kW
A. Dewatered cake 75% 1,000 294 706 71% 480 880–1,180
B. Same product from a 90% slurry 90% 2,500 294 2,206 88% 1,500 2,760–3,680

Case B has to evaporate about three times as much water as Case A to make the same dried product. That multiplies heater or waste-heat demand, exhaust volume and condenser duty. The 2,450 kJ/kg figure is approximate latent heat, not the fuel bill; 4,500–6,000 kJ/kg is a planning band for a real convective or indirect dryer until an air or jacket balance is done. Electrical demand for presses, pumps, fans, agitators and bagging should be listed separately.

A published claim of “75–85% mass reduction” is only true for a high starting moisture. The 75% cake above loses about 71% of its mass on the way to 15% moisture. If the commercial target is FOM at, say, 40% moisture rather than 15%, evaporation falls further: the same 1,000 kg/h of 75% cake would give 417 kg/h of product and only 583 kg/h of evaporation. The legal grade and the handling grade must not be mixed up in the same sentence of an enquiry.

Common specification mistakes to avoid

  • Sending raw digestate or LFOM to a thermal dryer because “we have biogas heat”, without first pressing or evaporating.
  • Quoting 500 kg/h or 5 TPH without saying whether that is slurry, dewatered cake or dried fertiliser, and at what moisture.
  • Drying to 10–20% moisture and labelling the bags as FCO FOM without checking the 30–70% moisture window and the other scheduled limits.
  • Selecting a fluid-bed dryer for a plastic cake that will not fluidise, or a band dryer for a liquid that will fall through the belt.
  • Assuming engine waste heat is free and always sufficient; jacket water and flue gas have temperature and schedule limits.
  • Ignoring corrosion (digestate can be acidic), odour treatment, and fire risk in dusty, organic dryers.

Frequently asked questions

Can I dry LFOM directly on a belt dryer?

Not usually in its scheduled 90–97% moisture form. Concentrate it first. A belt dryer is a candidate once you have a spreadable solid or a thick concentrate, not a thin liquid.

Does drying always preserve NPK?

No. Nitrogen, in particular, can be lost if the product is overheated or if ammonia is stripped into the exhaust. Multi-zone, moderate temperatures reduce that risk; they do not eliminate it. Any nutrient claim should be based on analysis of the actual dried product, not on a brochure phrase.

Do I need a trial?

Yes, if the feedstock can vary (press mud, cattle dung, poultry litter, food waste and municipal organics do not dry the same way), if the cake is sticky, or if you plan to use waste heat at a limited temperature. A rheology and drying-curve trial is more useful than a catalogue capacity.

Where can I read GTI’s digestate guidance?

Start with the digestate drying and LFOM and PROM pages. Related equipment families are described under drying machines on this site, including belt dryers.

About Genex Tech Industries LLP (GTI Group)

Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray dryers, band and belt dryers, rotary drum dryers, flash dryers, fluidised-bed and vibratory fluid-bed dryers, paddle dryers, vacuum dryers, heat pump dryers and refractance window dryers, as published on gtidryers.com. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See also the drying machines section of this site and GTI’s digestate drying solutions page.

Sources and authorship

  • The Fertiliser (Inorganic, Organic or Mixed) (Control) (Third) Amendment Order, 2025, S.O. 1477(E), 27 March 2025, Gazette of India Extraordinary, CG-DL-E-29032025-262118, setting FOM moisture at 30–70% and LFOM moisture at 90–97% by weight.
  • Published digestate and LFOM/PROM pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com, and the drying-machine pages on epcprojects.in.

The worked example is an illustrative calculation from the stated assumptions, not a plant measurement or a performance guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named process engineer, and no individual is cited as having approved the technical content. Please treat it as a specification aid pending engineering review of any project-specific design.

Next step

If you are planning digestate or LFOM drying at a CBG or biogas plant, email mktg@gtidryers.com or use the contact page on this site. Send the feedstock, whether the stream is liquid, slurry or dewatered cake, inlet and target moisture, the intended fertiliser grade (including any FCO specification), required product rate, available waste heat or steam, and the installation location. Related guides cover belt dryers for food processing, rotary versus flash dryers and how to choose the right industrial dryer.