When should you use a refractance window dryer for fruit and vegetable purees? Use it when the feed is a spreadable puree, paste or thin layer and you need continuous drying at a moderate product temperature, with a sheet or flake that can later be milled. Heat is supplied by circulating hot water beneath a transparent conveyor; the product is not tumbled in a drum and is not atomised into a spray chamber. A refractance window dryer is not a substitute for a belt dryer of slices or dices, and it is not automatically a substitute for a spray dryer of a dilute extract. Choose it for the feed form and the temperature history, then size it on evaporation and belt area, not on a marketing comparison of “quality”.
This guide is for fruit-, vegetable- and ingredient-plant engineers comparing thin-film drying with spray and belt options. Moisture is on a wet basis unless stated otherwise. Nutrient or colour advantages reported in the literature are product-specific; they are not a performance guarantee for any installation.
How does a refractance window dryer work?
The product is spread as a thin, uniform layer on a food-grade transparent belt. Heated water circulates under the belt and transfers energy through the film, mainly by conduction, with radiation and a controlled airflow to carry vapour away. As the layer dries, heat transfer through the film becomes less effective, which is the “window” behaviour described in the engineering literature: wet product accepts heat readily, while a drier film is less aggressively heated.
Nindo and Tang (2007), in a review of refractance-window dehydration, report circulating water typically at 95–97 °C, with the product temperature usually remaining below 70 °C. Those are published operating observations for the technology, not a GTI catalogue rating. Genex Tech Industries LLP (GTI Group) describes the same arrangement — hot-water heat transfer through a transparent conveyor to a thin product layer — on its refractance window dryer page, and lists fruit and vegetable purees, herbal extracts and selected functional-food ingredients as candidate feeds. Construction is described as food-grade stainless steel (SS304 / SS316), with capacity custom-engineered. No standard kg/h rating is published on that page, which is appropriate: belt width, layer thickness, residence time and inlet moisture set capacity.
How does it compare with a spray dryer or a belt dryer?
| Question | Refractance window | Spray dryer | Band / mesh-belt dryer |
|---|---|---|---|
| Feed form | Spreadable puree, paste or thin slurry | Pumpable liquid or stable slurry | Slices, dices, flakes, herbs or other particulates |
| How heat is applied | Hot water under a transparent belt; product in a thin layer | Hot air or gas contacting atomised droplets | Hot air through or across a product bed |
| Typical product temperature | Often kept below about 70 °C in published systems with 95–97 °C water | Particle temperature is limited while surface moisture evaporates, but inlet gas is much hotter | Set by zone air temperature; beds can be uneven if loading varies |
| Product form leaving the dryer | Sheet, flake or mat, usually milled afterwards | Fine powder of spray-dried morphology | The same pieces that were fed, in dried form |
| Main capacity driver | Evaporation, layer thickness and belt area | Evaporation, atomisation and air flow | Evaporation, bed depth, belt area and residence time |
A spray dryer is still the practical choice when you already have a dilute, pumpable extract and you want a free-flowing powder in one step. It becomes less attractive if the puree must be watered down only so that it can be atomised: that extra water is extra evaporation. A belt dryer remains the practical choice for mango slices, onion flakes or herbs that should keep their piece identity. Related application pages include GTI’s food ingredient dryers and the fruit and vegetable dehydration overview on foodtechprojects.com.
Worked example: 100 kg/h of dried puree solids at 4% moisture
Take an illustrative mango or mixed-fruit puree at 80% moisture that must be dried to a flake or powder at 4% moisture, with a packing rate of 100 kg/h. Dry solids are 100 × 0.96 = 96 kg/h. The puree feed is 96 / (1 − 0.80) = 480 kg/h, and evaporation is 380 kg/h.
| Item | Value | Notes |
|---|---|---|
| Dried product | 100 kg/h at 4% moisture | After milling if a powder is required |
| Puree feed at 20% solids | 480 kg/h | 80% moisture, wet basis |
| Water evaporated | 380 kg/h | Sets heater, water-circuit and exhaust duty |
| Approximate latent heat | 259 kW | At 2,450 kJ/kg |
| Indicative thermal input | 475–635 kW | At 4,500–6,000 kJ/kg, until a measured heat balance is available |
The latent-heat load does not disappear because the product is cooler than in a hot-air dryer. Water still has to be evaporated. The technical advantage, when it is real, is the temperature history and the fact that a concentrated puree does not have to be diluted. If the same 96 kg/h of solids were diluted to 15% solids so that a spray dryer could atomise the feed, the feed rate would rise to 640 kg/h and evaporation to 540 kg/h — about 40% more water than the 380 kg/h of the thin-film case. That comparison is the reason to test the puree as it is, rather than assuming a spray dryer is equivalent.
Belt area follows from layer thickness and residence time. Those must be measured: a thicker, high-sugar layer dries more slowly and can stick. GTI does not publish a standard belt area, and this article does not invent one. Ask for a trial that records water temperature, layer thickness, residence time, product temperature and final moisture.
Common specification mistakes to avoid
- Choosing a refractance window dryer for slices or whole herbs that belong on a belt dryer, or for a dilute extract that is already set up for spray drying.
- Assuming that “low-temperature drying” means a lower energy bill; the evaporation load is still set by the mass balance.
- Treating published colour or nutrient results from one fruit as a guarantee for another puree.
- Letting layer thickness vary across the belt, which produces wet streaks and over-dried edges.
- Omitting cooling, milling, screening and packing-room humidity from the scope.
- Buying on a nameless “kg/h” figure without puree solids, target moisture and a stated product form (sheet, flake or powder).
Frequently asked questions
Does a refractance window dryer always retain more nutrients than a spray dryer?
Not automatically. Several studies report good colour and bioactive retention when product temperature stays moderate, but the result depends on the puree, the layer, the residence time and how the spray-dryer comparison was run. Specify the quality tests you will use, and confirm them on a trial.
Can it dry coconut milk or other fatty liquids?
Only if the feed forms a stable, uniform layer and the fat does not foul the belt or smear in the mill. Coconut liquids are often spray-dried with a carrier. Do not assume a thin-film dryer is interchangeable; send the formulation and ask for a trial. Coconut-specific drying is covered separately in the site’s article on industrial coconut dryers.
Do I need a trial?
Yes, for high-sugar fruits, sticky pastes, or any product whose colour or activity is a selling point. Agree how layer thickness will be controlled and how the dried sheet will be cooled and milled.
Where can I read GTI’s own pages?
Start with the refractance window dryer and food ingredient dryers pages, and the fruit and vegetable overview on foodtechprojects.com. This site’s drying machines section lists the equipment families installed from here.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray dryers, band and belt dryers, rotary drum dryers, flash dryers, fluidised-bed and vibratory fluid-bed dryers, paddle dryers, vacuum dryers, heat pump dryers and refractance window dryers, as published on gtidryers.com. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See also the drying machines section of this site and GTI’s food drying systems page.
Sources and authorship
- Nindo, C.I.; Tang, J. “Refractance Window Dehydration Technology: A Novel Contact Drying Method”, Drying Technology, 2007, 25(1), 37–48, doi:10.1080/07373930601152673 (circulating water typically 95–97 °C; product temperature usually below 70 °C).
- Published refractance-window and food-ingredient pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com and foodtechprojects.com, and the drying-machine pages on epcprojects.in.
The worked example is an illustrative calculation from the stated assumptions, not a plant measurement or a performance guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named process engineer, and no individual is cited as having approved the technical content. Please treat it as a specification aid pending engineering review of any project-specific design.
Next step
If you are considering a refractance window dryer for a puree or paste, email mktg@gtidryers.com or use the contact page on this site. Send the product, solids or moisture, viscosity or a note on how it spreads, target moisture, required dried output, quality tests (colour, activity or microbiology), utilities and the installation location. Related guides cover belt dryers for food processing, spray-dryer sizing and how to choose the right industrial dryer.
