Case Hardening in Food Drying: Causes, Tests and Zone-Profile Fixes

What is case hardening in food drying, and how do you stop it? Case hardening is a dry, rigid crust that forms on slices or pieces when the surface loses water faster than moisture can move out from the core. The product feels dry at the discharge but is still wet inside, so it fails moisture tests, cakes or moulds in the pack, and rehydrates poorly. The usual cause is too much drying force too early: hot, dry air on wet product, often made worse by thick or uneven loading. The fix is a staged profile in which the first zones run with humid recirculated air, so the surface stays moist while the piece heats through, and later zones lower the humidity and the temperature to finish, plus a test that measures the core rather than the surface.

This guide is for production and quality managers on belt, band, tray and heat pump dryers for onion, garlic, ginger, fruit, vegetables and herbs. Moisture is on a wet basis unless stated otherwise.

Why does case hardening happen?

Drying removes water from the surface first; water inside must then diffuse outwards. If the surface dries and its cells collapse before the inside has warmed and started to move water, the outer layer becomes a barrier. The IUFoST teaching resource on food drying gives a familiar example: operators who raise air temperature on mango slices to about 80 °C to speed up drying can find that drying actually takes longer, because a skin forms that traps moisture, and the slices look and feel dry enough to pack while still wet inside. The same resource notes that temperatures of about 50–55 °C are often best for food drying.

A review in Drying Technology on the role of relative humidity (RH) in hot-air drying of fruits and vegetables (2022, vol. 40, no. 11) explains the mechanism. Higher RH mainly increases heat transfer into the product; lower RH mainly increases surface evaporation. Low RH early produces a rigid crust that fixes the volume; starting at high RH and then stepping RH down mitigates case hardening, promotes a porous structure and can improve drying efficiency compared with continuous dehumidification. The 2018 review of shrinkage during drying in Comprehensive Reviews in Food Science and Food Safety also discusses how case hardening restricts shrinkage.

How do you tell case hardening from simple under-drying?

Symptom Case hardening Under-drying Scorching
Feel at discharge Dry, hard surface Soft, pliable Hard, brittle
Cut section Darker, moist or translucent core Uniformly moist Dark surface or edges
Moisture after 12–24 h sealed Rises at the surface; bag may feel tacky Uniformly high Low
Colour Often normal outside Normal Browned, burnt notes
Rehydration Slow, incomplete Fast Poor, with off-flavour

A practical test: take a sample at discharge, cut several pieces in half and look at the core; seal the rest in a moisture-proof bag for 12–24 hours, then measure moisture (and water activity if your lab has it) on the whole sample. If the sealed sample feels damp or the surface becomes tacky as core moisture moves outwards, case hardening is likely. A surface probe or a hand check at the discharge is not enough.

Worked example: why a “dry” piece fails the moisture test

Consider an illustrative onion slice in which 60% of the dry solids sit in an outer layer dried to 4% moisture and 40% in a core still at 18%. Water in the outer layer = 0.60 × 4/96 = 0.025 kg per kg of dry solids; water in the core = 0.40 × 18/82 = 0.088 kg. Total water = 0.113 kg on 1.113 kg of product, an average of about 10%, well above an illustrative specification of 6% (use your own buyer’s limit). The piece feels dry because the surface is at 4%. In the bag, moisture redistributes, raising surface moisture and the risk of caking and mould.

Now the line view. At 1,000 kg/h of sliced onion at an assumed 87% moisture dried to 6%, dry solids are 130 kg/h, product is 138 kg/h and evaporation is about 862 kg/h. If the plant answers case hardening by raising the final-zone temperature, it usually scorches the surface before the core gives up its water. The better answer is in the early zones.

What zone profile prevents it?

Stage Goal Air condition What to watch
Entry / first zone Heat the piece through while the surface stays wet Moderate-to-high temperature with higher RH, using partial exhaust recirculation Product surface should stay moist; avoid hot, dry fresh air here
Middle zones Main water removal RH stepped down; temperature held within product limits Bed uniformity; wet streaks across belt width
Finishing zone Reach target moisture without browning Lower temperature, low RH Product temperature, colour, over-drying
Cooling Stop heat damage; allow equalisation Ambient or conditioned air Packing temperature and room humidity

Exact temperatures and RH depend on the product and must be found by trial. GTI’s guide to energy-efficient band dryers notes that colour darkening, flavour loss and case hardening are common when a single high air temperature is used along the whole dryer, and describes multi-zone profiles with partial exhaust recirculation within product-quality and humidity limits. Recirculating humid exhaust in the first zone can reduce heat demand as well as protecting the product, but only within the humidity limit that still lets the dryer remove water.

Other causes to check

  • Slice thickness and uniformity: thick or variable slices dry unevenly; check the slicer first.
  • Bed depth and loading: overloading creates wet cores; underloading lets air bypass.
  • Air distribution: measure air velocity across belt width; fix wet edges at the source.
  • Sugar content: high-sugar fruit is more prone to surface crusting and stickiness.
  • Pre-treatment: blanching or other treatments change skin permeability; validate any change.

Which dryer types help?

A multi-zone mesh belt dryer or band dryer with independent zone temperature, airflow and recirculation dampers gives the most direct control. A heat pump dryer, which GTI describes as operating typically between 30 °C and 60 °C with PLC-based temperature and humidity control, suits heat-sensitive products where humidity can be programmed by stage. For purees rather than pieces, see the refractance window dryer guide.

Frequently asked questions

Can case-hardened product be rescued?

Sometimes, by tempering it (holding it so moisture equalises) and then finishing at lower temperature, but quality is usually below that of product dried correctly. Prevention is cheaper.

Does lower temperature always prevent it?

Not by itself. Very dry air at moderate temperature can still crust the surface. The humidity profile matters as much as temperature.

Does humid air in the first zone slow the dryer down?

Not necessarily. The review cited above reports that starting at high RH and stepping it down can improve drying efficiency compared with continuous dehumidification. Confirm on your product.

Where can I read more?

See how to specify a belt dryer for food processing, GTI’s onion dryer page and the fruit and vegetable dehydration overview on foodtechprojects.com.

About Genex Tech Industries LLP (GTI Group)

Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including band and belt dryers, heat pump dryers, fluidised-bed and vibratory fluid-bed dryers, rotary drum dryers, spray dryers, flash dryers, paddle dryers, vacuum dryers and refractance window dryers, as published on gtidryers.com. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See GTI’s food drying systems page and this site’s belt dryer page.

Sources and authorship

  • IUFoST, food drying teaching resource, “Drying – Part 1” (sections on air temperature and case hardening).
  • “The influence mechanism and control strategy of relative humidity on hot air drying of fruits and vegetables: a review”, Drying Technology, 2022, 40(11), doi:10.1080/07373937.2021.1943669.
  • “Shrinkage of Food Materials During Drying: Current Status and Challenges”, Comprehensive Reviews in Food Science and Food Safety, 2018, doi:10.1111/1541-4337.12375.
  • Published food-drying pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com and foodtechprojects.com.

The worked examples are illustrative calculations from stated assumptions, not plant measurements or guarantees. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named food engineer, and no individual is cited as having approved the technical content.

Next step

If case hardening, wet cores or uneven moisture are costing you product, email mktg@gtidryers.com or use the contact page. Send the product and cut size, fresh and target moisture, current zone temperatures and airflow if known, required output, heat source and the installation location.