CTC Tea Dryer Troubleshooting: Stewing, Case Hardening and Exhaust Temperature

Why does a CTC tea dryer produce stewed or case-hardened tea, and how do you fix it? Usually the exhaust temperature has drifted out of its window. UPASI Tea Research Foundation guidance for conventional CTC dryers is an inlet of 100 ± 5°C and an exhaust of 54.4 ± 2.7°C. Below about 49°C, fermentation continues and the tea “stews” (soft liquor). Above about 57.2°C, the surface dries too fast and the particles case-harden (harsh liquor, poor keeping). The target is made tea at 2.5–3.0% moisture. Most exhaust drift comes from changes in dhool load or moisture, air flow or heat input, so troubleshoot those before touching the burner set point.

This guide is for tea factory managers, factory engineers and estate engineering teams. “Dhool” is the fermented leaf fed to the dryer. All moisture figures are on a wet basis.

What do the published operating windows say?

The UPASI Tea Research Foundation CTC manufacturing guidance gives these figures for conventional (tray/endless-chain) dryers:

Parameter Guidance Effect outside the window
Inlet air (CTC) 100 ± 5°C Too high raises case-hardening risk; too low slows drying
Exhaust air 54.4 ± 2.7°C (130 ± 5°F) Below 49°C: stewing. Above 57.2°C: case hardening
Final moisture 2.5–3.0% Below 1.0%: quality loss. 3.5% and above: poor keeping

The same guidance says case hardening is seldom seen in fluidised bed dryers. Each particle is surrounded by moving air, so bed temperatures stay uniform. It also notes these dryers produce blacker teas with better appearance and bloom. This is one reason many factories have moved to fluid bed and vibro fluid bed dryers. Even so, fluid bed dryers can over- or under-fire when the load or air balance is wrong.

Research continues on the settings. Kumar, Kumar and Dashora (Journal of Food Process Engineering, August 2024) modelled single CTC particles. They found that 80–100°C air did not dry effectively in their model and suggested 110–130°C for drying times of about 20–25 minutes in single-tray or slow conveyor dryers. Different dryer designs need different settings. The exhaust condition, though, is a useful control signal on any design because it shows how much drying the air has done.

Why is exhaust temperature the key signal?

In a convective dryer, the air cools as it evaporates water. With fixed inlet temperature and air flow, the exhaust temperature tells you whether the air is doing more or less drying than designed:

  • Exhaust falling: more water is arriving than the air can carry (higher dhool feed rate or wetter dhool), or air flow or heat input has dropped.
  • Exhaust rising: less water is arriving (lower feed or drier dhool), or there is more air or heat than the load needs.

Worked example: how load changes move the exhaust

Basis: 1,000 kg/h of dhool at 65% moisture dried to 3% made tea. The GTI black tea dryer page gives a 60–70% to 2–3% range for this duty.

Item Calculation Result
Dry solids 1,000 × 0.35 350 kg/h
Made tea at 3% 350 ÷ 0.97 361 kg/h
Water evaporated 1,000 − 361 639 kg/h
Heat taken up by the water (assumed 2,600 kJ/kg incl. sensible heat) 639 × 2,600 ≈ 1.66 GJ/h (≈ 460 kW)
Air needed for a 100°C inlet to 54°C exhaust drop (46 K, cp 1.02 kJ/kg·K) 1.66 GJ ÷ (1.02 × 46) ≈ 35,400 kg/h dry air (before losses)

Now suppose the withering and rolling sections send 10% more dhool for half an hour (1,100 kg/h) while air and heat stay the same. The air must absorb about 10% more evaporation heat, so its temperature drop grows from about 46 K to about 51 K. The exhaust falls to roughly 49°C, the edge of the stewing zone. A 10% surge is easy to miss on the floor, but the exhaust thermometer shows it within minutes. The figures are a simplified balance that ignores heat losses. Use it to understand trends, not to set a specific dryer.

Troubleshooting table

Symptom Likely causes What to check Typical correction
Soft, “stewy” liquor; moisture above 3.5% Exhaust too low: overloading, wet dhool, low air flow, low heat Feed rate, dhool moisture, fan damper and belt/screen condition, heater output Even out feeding; restore air flow; then adjust heat
Harsh liquor, hard particles, poor keeping Exhaust too high or inlet too hot; underloading Inlet and exhaust temperatures, bed depth or tray loading Restore load or reduce heat; avoid running hot on light loads
“Bakey” or burnt notes; moisture below 1% Over-firing: excess residence time or heat in final zone Final zone temperature, residence time, speed or damper settings Shorten residence time or reduce final zone heat
Uneven colour or moisture across the batch Uneven spreading; air maldistribution; worn trays or grid Spreader settings, perforation blockage, side leakage Clean grids and trays; fix spreading; rebalance dampers
Loss of bloom; more fibre and dust Excess air velocity or mechanical action in late zones Air velocity in final zone, vibration amplitude, cyclone load Reduce late-zone velocity; check dust collection

How do you keep the dryer in its window?

  • Steady feed. Use a buffer or controlled feeder between fermenting and drying so dhool arrives at a steady rate.
  • Measure the right temperatures. Calibrated inlet and exhaust probes, logged every shift, and a moisture check on made tea at least each shift.
  • Clean air paths. Blocked perforations and fouled heat exchangers reduce air flow and heat, and the exhaust falls even at normal load.
  • Control on exhaust. Automatic heat-input control on exhaust temperature, with alarms at the stewing and case-hardening limits, reduces operator-dependent swings.
  • Raw material quality. The Tea Board’s public notice of 11 March 2019 directs factories to reject discoloured, bruised, fermented and scorched leaf, and warns that teas failing quality standards may be treated as tea waste. A dryer cannot correct poor leaf.

Frequently asked questions

Do these numbers apply to orthodox tea?

The principle (watch exhaust condition and final moisture) applies, but orthodox leaf is larger and more fragile, and settings differ. Use your research institute’s guidance and factory trials.

Does a fluid bed dryer remove the need for exhaust control?

No. It reduces case-hardening risk, but overloads and air imbalance still cause under-firing, and too much late-zone air can damage bloom.

Can heat recovery change these settings?

Recirculating some exhaust or preheating air saves fuel, but it changes inlet humidity and drying rate. Recheck exhaust targets and made-tea moisture after any heat-recovery change.

About Genex Tech Industries LLP (GTI Group)

Genex Tech Industries LLP (GTI Group) designs and manufactures industrial tea dryers. Its tea drying systems and black tea pages describe vibro fluid bed and combination (hybrid) dryers, with heating options including electric, steam and biomass. See also our guide on choosing an industrial tea dryer for CTC, orthodox and green tea, our article on case hardening in food drying, and this site’s drying machines page. The head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India.

Sources and authorship

  • UPASI Tea Research Foundation, “CTC” manufacturing guidance (drying section), accessed November 2026.
  • Kumar, Kumar and Dashora, “Impact study of operating parameters on drying evolution of spherical tea particle under convective influence”, Journal of Food Process Engineering, August 2024.
  • Tea Board of India, Public Notice on Maintaining Quality of Tea, Ref. 5(41)/DTD/PPC, 11 March 2019.
  • Published tea drying pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com.

The worked example is a simplified, illustrative heat balance from stated assumptions. It is not a plant measurement or setting for any specific dryer. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named engineer, and no individual is cited as having approved the technical content.

Next step

Fighting stewing, case hardening or high fuel use on a tea dryer? Email mktg@gtidryers.com or use the contact page. Send the tea type (CTC, orthodox or green), dhool feed rate and moisture, target made-tea moisture, current dryer type, inlet and exhaust readings, fuel, and the factory location.