How big a maize dryer do you need, and what will it cost to run? Start from water removed, not grain tonnage. Taking a tonne of maize from 22% to the 14% moisture used in Indian trade specifications removes about 93 kg of water. At the 2,000–3,000 Btu per pound of water that University of Wisconsin Extension gives for continuous-flow grain dryers, that water needs roughly 430–650 MJ of heat per wet tonne. Drying below 14% gives away saleable weight and burns more fuel. Drying too hot or cooling too fast cracks kernels.
This guide is for feed mills, starch plants, grain-based distilleries and aggregators planning mechanical drying. Moisture is on a wet basis throughout, as used in grain trade.
Why is mechanical maize drying a live issue in India?
The FICCI–YES Bank India maize sector knowledge report (May 2026) says about 12.5 million tonnes of maize went to ethanol production in FY 2025-26 under the E20 programme. It puts maize post-harvest losses at about 3–4%, driven mainly by inadequate drying, fragmented aggregation and poor storage, citing a MoFPI loss study. It also notes that maize needs 10–15 days of drying to reach 13–14%. Farmers mostly sun-dry, and poor practice can leave grain at around 18%, where fungal growth and aflatoxin risk rise. One of the report’s five recommended pathways is scaling “scientific drying”.
Trade specifications set the target. NAFED’s procurement terms for maize supplied to distilleries refer to FCI FAQ norms with 14% maximum moisture. The NCDEX maize contract uses 14% as basis with up to 15% permissible. Buyers with their own specifications may differ, so check yours.
How much water comes out per tonne?
Weight after drying = initial weight × (100 − initial moisture) ÷ (100 − final moisture). For 1,000 kg of wet maize dried to 14%:
| Incoming moisture | Weight at 14% (kg) | Water removed (kg per wet tonne) | Heat at 4.65–6.98 MJ/kg water (MJ per wet tonne) |
|---|---|---|---|
| 18% | 953 | 47 | 216–325 |
| 20% | 930 | 70 | 325–487 |
| 22% | 907 | 93 | 432–649 |
| 25% | 872 | 128 | 595–893 |
The heat range converts UW Extension’s 2,000–3,000 Btu/lb of water (1 Btu/lb = 2.326 kJ/kg). The lower figure is for column dryers with energy-saving features, the upper for a well-maintained dryer without them. Treat these as benchmarks from US grain-dryer practice, not guarantees for any design.
Worked example: a 20 t/h intake at 22%
- Water removed: 20 × 93 = about 1,860 kg/h.
- Heat: 1,860 × 4.65–6.98 MJ/kg ≈ 8,650–12,980 MJ/h, or about 2.4–3.6 MW.
- Fuel: with biomass at an assumed 14 MJ/kg as fired and the burner losses already inside the benchmark, about 620–930 kg/h. With other fuels, divide by their usable heating value.
- Output: about 18.1 t/h of maize at 14%.
Over-drying cost. If the same grain is dried to 12% instead of 14%, output falls from 907 to about 886 kg per wet tonne. That is about 21 kg less saleable weight per tonne and about 21 kg more water to evaporate. At an illustrative maize value of ₹24 per kg (use your own), 18 t/h of output over-dried by 2 points loses roughly 18,000 kg × 2.27% × ₹24 ≈ ₹9,800 per hour, plus the extra fuel. UW Extension’s batch dryer fact sheet makes the same point: over-dried grain “reduces grain weight to sell and increases energy use”.
Which dryer suits maize?
In large grain-handling systems, continuous-flow column dryers (cross-flow, mixed-flow and in-bin counter-flow types) are widely used, as UW Extension’s continuous flow dryer fact sheet describes. GTI’s grain dryers page lists other continuous types that suit different plant situations:
| Dryer (GTI grain range) | When it fits maize | Watch-outs |
|---|---|---|
| Mesh belt dryer | Continuous drying in a processing plant with zoned temperatures; corn, paddy, soybean | Footprint per tonne; even bed loading |
| Rotary drum dryer | Large-capacity grain or feedstock preparation | Kernel breakage from tumbling; grain temperature control |
| Fluid bed / vibratory fluid bed dryer | Grain conditioning, seed and smaller grains | Fan power for whole maize kernels; capacity per unit area |
The choice depends on whether you are drying incoming grain for storage (high tonnage, seasonal) or conditioning grain inside a process (steady, year-round). It also depends on fuel, space, end use and how much kernel damage your buyer accepts. Ask any supplier, including GTI, to show evaporation rate, heat per kg of water and the expected kernel-damage effect on the same basis.
Grain quality: temperature, cooling and moisture spread
- Stress cracks. UW Extension notes that rapid cooling inside the dryer causes stress cracks, and recommends moving hot grain to a cooling bin for slower cooling, transferring it 1–3 points above the final moisture depending on the cooling method. Cracked kernels break in handling and lower grain value.
- End use sets the temperature limit. Feed, dry-grind ethanol and starch (wet milling) buyers tolerate heat differently. Wet millers are usually the strictest, because heat damage reduces starch recovery. Agree a maximum grain temperature with your buyer or process team.
- Moisture spread. A 14% average can hide 12% and 17% kernels. Wet kernels support mould growth in storage. Measure spread at commissioning, and use discharge controls that sense grain moisture.
- Aflatoxin. Drying quickly after harvest limits fungal growth, but it does not remove aflatoxin already present. Test incoming lots, and keep wet grain waiting times short.
What should be in your enquiry?
- Intake tonnage per hour or day, and the season length
- Incoming moisture range (with how it was measured) and target moisture
- End use: feed, ethanol, starch or seed; maximum grain temperature
- Fuel available (biomass, husk, gas, steam) and its cost
- Wet-grain holding and cooling/storage arrangements
- Dust and emission limits, and the installation location
Frequently asked questions
Is sun-drying enough for a distillery or feed mill?
It can work in dry weather for small volumes. The FICCI–YES Bank report shows why industrial buyers struggle with it: 10–15 days of drying, weather risk, and lots arriving near 18%. A mechanical dryer turns drying into a controlled, measured step.
Can a distillery dry its own wet maize?
Yes, if it has wet-grain reception, a dryer sized for peak intake, and cooling and storage. Some plants also use spare steam or waste heat. Check the heat balance and grain-temperature limits first.
Does drying affect DDGS quality?
Mostly indirectly: mouldy or heat-damaged grain carries through to the co-product. DDGS drying itself is a separate step. See our DDGS dryer guide.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial dryers, including the grain, corn starch and animal feed and agro drying systems described on gtidryers.com. See also this site’s drying machines page and our guides on starch flash dryer energy and choosing an industrial dryer. The head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India.
Sources and authorship
- FICCI and YES BANK, India maize sector knowledge report, May 2026 (ethanol use FY 2025-26, post-harvest losses, drying practice).
- NAFED procurement letter for maize for ethanol distilleries (FCI FAQ norms: 14% maximum moisture), 2024.
- NCDEX, maize contract press release and contract parameters (14% basis, 15% permissible).
- Scott Sanford, University of Wisconsin Extension, “Continuous Flow Dryers” fact sheet ENCON2.3, December 2012, and the companion “Batch Dryers” fact sheet.
- Published grain and feed drying pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com.
The worked example uses stated benchmarks and illustrative assumptions (fuel heating value, grain value). It is not a plant measurement or performance guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named engineer, and no individual is cited as having approved the technical content.
Next step
Planning a maize dryer for a feed mill, distillery or aggregation centre? Email mktg@gtidryers.com or use the contact page. Send the intake rate, incoming and target moisture, end use and grain temperature limit, fuel, storage arrangements and the installation location.
