What should an extruded fish feed dryer achieve? It should take pellets from the extruder, typically 20–24% moisture according to an extrusion reference published by FAO, down to a steady safe moisture. That is commonly 8–10% in published guidance, while GTI’s fish feed page gives 10–12%. It must do this without cracking or weakening the pellets and without wasting heat. With feed ingredient costs high in 2026, the expensive mistakes are over-drying (it gives away saleable weight and burns fuel) and uneven drying (it forces the whole batch to be over-dried so that the wettest pellets pass).
This guide is for aquafeed plant managers and project engineers. All moisture figures are on a wet basis.
Why is fish feed drying a cost issue now?
BusinessLine reported on 6 November 2026 that shrimp feed prices had risen by ₹10–16 per kg, to roughly ₹1.2–1.75 lakh per tonne depending on brand, because fishmeal, fish oil and soybean meal costs had gone up. In its FY 2025-26 annual report, as covered by Aquafeed.com, IFB Agro said it expects 2026-27 to remain challenging for aquafeed because of rising input costs and restrictions on shrimp feed price increases in Andhra Pradesh. When raw materials are expensive and selling prices are capped, every kilogram of moisture given away in the dryer comes straight out of margin.
New research also matters for dryer settings. A pilot study by Graff, Maichel and Alavi in Processes (10 May 2026) dried extruded trout feed from about 21–22% to 3.5–5.0% on a heated-air conveyor dryer and cooler. Raising throughput from 82 to 121 kg/h increased pellet durability index (PDI) from 82.8% to 88.0%. Raising drying temperature from 93°C to 115°C lowered final moisture but slightly lowered PDI (not statistically significant). The authors linked durability mainly to shrinkage-induced structural weakness, which depends on drying rate.
Which dryer types are used?
Bouvier and Brisset’s aquafeed extrusion paper, hosted by FAO, describes horizontal belt dryers (single or multi-pass, with single-pass or recirculating air) and vertical counter-flow dryers as the usual designs. GTI’s fish feed drying page lists:
| Dryer | Typical use in aquafeed | Points to check |
|---|---|---|
| Mesh belt dryer (single or multi-pass) | Floating and sinking pellets, shrimp feed; most common continuous choice | Even bed depth across the belt, zone air control, fines handling at transfer points |
| Fluid bed dryer | Small pellets and granules | Air velocity versus attrition; fines in exhaust |
| Vibratory fluid bed dryer | Pellet and granule drying, conditioning and cooling | Residence-time control, clumping of fresh pellets |
| Heat pump dryer | Low-temperature drying of sensitive formulations | Lower drying rates; capacity per unit area; electricity cost |
Worked example: what does over-drying cost?
Basis: a line producing 5,000 kg/h of dried feed at a 9% target, from pellets leaving the extruder at 22%.
| Item | Calculation | Result |
|---|---|---|
| Dry solids | 5,000 × 0.91 | 4,550 kg/h |
| Wet pellets to dryer | 4,550 ÷ 0.78 | 5,833 kg/h |
| Water removed at 9% target | 5,833 − 5,000 | 833 kg/h |
| Product if over-dried to 6% | 4,550 ÷ 0.94 | 4,840 kg/h |
| Saleable weight lost | 5,000 − 4,840 | 160 kg/h (3.2%) |
At an illustrative selling price of ₹50 per kg (use your own), 160 kg/h is ₹8,000 per hour of lost revenue. Over 6,000 operating hours that is about ₹4.8 crore a year, before counting the extra fuel. The extra 160 kg/h of water also needs heat. Bouvier and Brisset give 2,325 kJ/kg as the energy for water removal. At an assumed 50% overall dryer efficiency, that is about 160 × 2,325 ÷ 0.5 ≈ 744 MJ/h, around 0.2 MW of heat used to remove water you could have sold.
The usual reason plants over-dry is uneven moisture across the bed, not a wrong set point. If the wettest pellets come out at 11% while the average is 9%, operators cut the target until the wettest pass. Narrow the spread and you can raise the average target safely.
Why do pellets come out uneven or weak?
Uneven bed and air distribution
On belt dryers, thin edges and thick centres dry at different rates. Check spreader settings, side seals and air distribution with moisture samples taken across the belt width, not just from the discharge mix.
Drying too hard, too early
Haubjerg and Veje (Drying Technology, 2018) studied how drying conditions affect the mechanical durability of extruded fish feed. Their work, and the 2026 pilot study, point the same way: the rate and conditions of drying change shrinkage and pellet structure. They do not give a single best temperature for every recipe. Settings need trials on your formulation and pellet size.
Moisture pick-up after the dryer
Pellets packed warm can sweat in bags, and coated pellets can pick up moisture in humid storage. Cool to near ambient before bagging, and agree a moisture (and, if your QA uses it, water activity) limit for the bagged product, not only at the dryer outlet.
Fines
Fines from transfer points and over-dry, brittle pellets reduce water stability and yield. Collect them, measure them, and check whether drying conditions or handling is the cause.
How should you compare dryer offers?
- Same basis. Ask for evaporation in kg of water per hour at stated inlet and outlet moisture, not just “t/h capacity”.
- Specific heat consumption. Ask for MJ per kg of water at a stated ambient condition. Do not compare plant quotes against pilot data: the 2026 pilot study measured 101–150 MJ per kg of water, many times a production dryer’s figure, because pilot units carry large fixed losses.
- Moisture spread. Ask what moisture variation across the bed the design targets and how it will be measured at commissioning.
- Air recirculation and exhaust humidity control. Recirculating part of the exhaust saves heat. Exhaust humidity should be controlled, not left fixed.
- Cleaning and fire safety. Fat-coated fines on hot surfaces are a fire risk. Ask about access, cleaning intervals and temperature interlocks.
Frequently asked questions
Should floating and sinking feeds use the same dryer settings?
Not necessarily. Pellet density, size and expansion differ, so residence time and air conditions usually differ too. Many plants keep recipe-wise settings and check moisture by recipe.
8–10% or 10–12% moisture: which is right?
Both ranges appear in published sources. The right target depends on formulation, storage climate, shelf life, water activity and the buyer’s or regulator’s specification. Set it with your QA team, then control to it with a margin.
Can a heat pump dryer replace a hot-air belt dryer?
For high-tonnage lines, heat pump drying rates and costs need careful checking. It suits sensitive or specialty formulations better. Our heat pump vs hot-air dryer guide explains the energy comparison.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial dryers for feed and food uses, including the fish feed, poultry feed and animal feed drying systems described on gtidryers.com. See also this site’s mesh belt dryer page and our guides on specifying a belt dryer and drying black soldier fly larvae, an emerging feed protein. The head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India.
Sources and authorship
- “Rising feed cost dampen shrimp farmers prospects despite higher volumes”, The Hindu BusinessLine, 6 November 2026.
- Aquafeed.com, “IFB Agro outlines growth strategy following acquisition of Cargill India’s aquafeed business” (FY 2025-26 annual report coverage), 2026.
- Graff, Maichel and Alavi, “Sorghum and Wheat-Based Extruded Aquatic Feed—Impact of Drying Parameters on Pellet Quality and Energy Efficiency”, Processes, 10 May 2026.
- Haubjerg and Veje, “An experimental approach towards increasing mechanical durability of extruded fish feed in the drying process”, Drying Technology, 2018.
- Bouvier and Brisset, “Aquafeed Twin Screw Extrusion Processing” (Clextral), 2006, hosted by FAO.
- Published feed drying pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com.
The worked example uses illustrative assumptions (price, operating hours, 50% efficiency). It is not a plant measurement or performance guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named engineer, and no individual is cited as having approved the technical content.
Next step
Planning a new aquafeed dryer or trying to stop over-drying on an existing line? Email mktg@gtidryers.com or use the contact page. Send pellet types and sizes, output rate, extruder outlet and target moisture, fuel or steam available, coating step, and the installation location.
