Is a heat pump dryer cheaper to run than a hot-air dryer? Often, for low-temperature drying of herbs, leaves, spices and botanicals, but not automatically. The answer depends on three numbers you can check before buying: the heat pump dryer’s SMER (specific moisture extraction rate, kg of water removed per kWh of electricity), the overall efficiency of your present hot-air dryer, and the ratio between your electricity price and your fuel price per kWh of heat. Replacing an electrically heated hot-air cabinet is almost always a clear win. Replacing a well-run biomass or steam-heated belt dryer needs the calculation below.
This guide is for owners and plant managers of spice, herb, tea-adjacent and botanical drying units. Moisture is on a wet basis (w.b.) unless stated otherwise.
Why are processors looking at heat pump dryers now?
Low-temperature process heat is a large share of industrial energy use. In an opinion article in The Hindu on 6 May 2026, the authors note that industry accounted for nearly half of India’s final energy consumption in 2025 and that heat and steam below 250 °C, largely produced by burning fossil fuels, is the backbone of food processing, textiles, chemicals, pharmaceuticals and paper. Drying of heat-sensitive products sits at the low end of that range, which is where heat pumps work best. That makes the heat pump dryer a practical option to evaluate, not just a trend to follow.
How does a heat pump dryer work?
A heat pump dryer runs the drying air in a closed or semi-closed loop. Warm air picks up moisture from the product; an evaporator coil then cools it below its dew point, so the water condenses and drains away; the refrigerant carries that recovered heat to a condenser, which reheats the now-dry air before it returns to the chamber. Genex Tech Industries LLP (GTI Group) describes this cycle on its heat pump dryer page, with drying temperatures typically between 30 °C and 60 °C, PLC-based temperature and humidity control, and operation that does not depend on outdoor humidity.
The key difference from a hot-air dryer is that the latent heat in the exhaust is recovered instead of being thrown away up the stack.
What is SMER and what values are realistic?
SMER is the kilograms of water removed per kWh of electricity used by the whole dryer: compressor, fans and controls. It is the number to compare, and it should be measured on your product, because it falls as the product gets drier and moisture becomes harder to remove.
Published values vary widely with product, temperature and design. A 2025 review of heat pump drying for fruits and vegetables in Foods (Zhu et al., 22 July 2025) cites, for example, a solar-assisted heat pump dryer for tomato and carrot with a SMER of 1.33 kg/kWh, and a simulated closed-circuit heat pump fluid-bed system reaching 2.8 kg/kWh when exhaust recirculation was increased. Treat such figures as indicative. Ask any supplier for SMER measured over a full batch on a product like yours, including fan power.
Worked example: heat pump vs hot air for a herb dryer
Assume 1,000 kg/day of fresh leaves at 80% moisture, dried to 10%.
- Dry matter = 1,000 × 0.20 = 200 kg; dried product = 200 ÷ 0.90 = 222 kg.
- Water removed = 1,000 − 222 = 778 kg/day.
- Evaporating 1 kg of water needs about 2,500 kJ, or 0.694 kWh, before any losses.
| Dryer (assumptions) | Energy per kg water | Energy per day |
|---|---|---|
| Hot-air dryer, overall efficiency 40% (fuel or electric heat) | 0.694 ÷ 0.40 = 1.74 kWh heat | about 1,350 kWh heat |
| Hot-air dryer, overall efficiency 50% | 1.39 kWh heat | about 1,080 kWh heat |
| Heat pump dryer, SMER 1.3 kg/kWh | 0.77 kWh electricity | about 600 kWh electricity |
| Heat pump dryer, SMER 2.8 kg/kWh | 0.36 kWh electricity | about 280 kWh electricity |
Overall efficiency here means the share of the fuel (or heater) energy that ends up evaporating water; fan power is excluded for the hot-air dryer and included in SMER for the heat pump. These are illustrative assumptions, not measured results for any GTI dryer.
The break-even test
Per kg of water, the heat pump costs electricity price ÷ SMER, and the hot-air dryer costs 0.694 × fuel cost per kWh of fuel energy ÷ efficiency. The heat pump is cheaper when:
electricity price per kWh < fuel cost per kWh × SMER × 0.694 ÷ efficiency
- With SMER 1.5 and 40% efficiency, the multiplier is 1.5 × 0.694 ÷ 0.40 = 2.6: electricity can cost up to 2.6 times as much per kWh as your fuel and the heat pump still wins on energy.
- With SMER 1.3 and 50% efficiency, the multiplier drops to about 1.8.
Illustration: if power costs ₹9 per kWh and your fuel costs ₹4 per kWh of fuel energy (price ÷ calorific value), the ratio is 2.25. The heat pump wins in the first case and loses in the second. Use your own tariffs, fuel prices and measured efficiencies. For an electrically heated hot-air cabinet, fuel cost equals electricity price, so any SMER above efficiency ÷ 0.694 (about 0.58 kg/kWh at 40% efficiency) wins; even a SMER of 1.3 uses about 45% of the electricity of a 40%-efficient electric cabinet.
Where does a heat pump dryer fit, and where does it not?
| Good fit | Poor fit |
|---|---|
| Heat-sensitive herbs, leaves, flowers and botanicals where colour, aroma or actives matter | Products that need high air temperatures, such as spray drying |
| Humid climates and monsoon months, when outdoor air limits hot-air dryers | Very high throughputs where cheap waste heat or steam is already available |
| Replacing electric-heated cabinet or tray dryers | Products that must be dried quickly at higher temperature to control spoilage |
| Sites with reliable power and no fuel handling | Sites with unreliable grid supply and no backup |
What are the practical limits?
- Drying time. Lower temperatures usually mean longer cycles. Size chambers or belts on measured drying curves, not on energy figures.
- Microbial control. Low-temperature drying preserves quality but does not, by itself, reduce microbial load to export specifications. Raw-material hygiene and any validated microbial reduction step remain essential for spices and herbs.
- Humidity profile. Very dry air early can crust the surface. A staged humidity profile helps; see our guide to case hardening in food drying.
- Maintenance. Dust and volatile oils foul evaporator and condenser coils, which lowers SMER. Plan filtration and coil cleaning.
- Capital cost. Heat pump dryers usually cost more to buy than simple hot-air dryers. Compare payback on your measured energy saving.
Questions to ask a supplier
- What SMER was measured, on which product, from what moisture to what moisture, and does it include fan power?
- What drying time and loading (kg/m²) were achieved in that trial?
- What temperature and humidity range can the system hold, and how is humidity controlled by stage?
- What backup heat or bypass is provided for very wet incoming product?
- How are coils protected from dust and oils, and how often must they be cleaned?
- Can a trial be run on my product before ordering?
Frequently asked questions
Does a heat pump dryer save energy for every product?
No. It saves most where drying is at low temperature and the exhaust would otherwise carry away a lot of latent heat. For high-temperature processes, other heat recovery options may suit better.
Can a heat pump be added to an existing belt dryer?
Sometimes, as a dehumidification or exhaust heat-recovery module. It depends on air flow, temperatures and space. A site survey and measured air data are needed.
What temperature should I dry spices and herbs at?
It depends on the product and the quality target. GTI quotes 30–60 °C for its heat pump dryers; trials on your material should set the profile.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including heat pump, band, mesh belt, vibratory fluid-bed, rotary drum and spray dryers, as listed on its gtidryers.com products page. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See GTI’s spice drying and herbal drying pages, the heat pump dryer page on foodtechprojects.com, this site’s mesh belt dryer page, and our guide on how to specify a belt dryer for food processing.
Sources and authorship
- Vrinda Gupta and Srinivas Ethiraj, “Why industrial heat pumps are a ‘clean heat’ opportunity for India”, The Hindu, 6 May 2026 (opinion).
- Zhu L. et al., “Heat Pump Technology in the Field of Fruit and Vegetable Drying: A Review”, Foods, 2025, 14(15), 2569, doi:10.3390/foods14152569.
- Published heat pump dryer pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com and foodtechprojects.com.
The worked example is an illustrative calculation from stated assumptions, not a plant measurement or guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named engineer, and no individual is cited as having approved the technical content.
Next step
Comparing a heat pump dryer with your present dryer? Email mktg@gtidryers.com or use the contact page. Send the product, fresh and target moisture, daily throughput, present dryer type and fuel, your electricity tariff and fuel price, and the installation location.
