How much tea dryer capacity does a factory need? Enough for the peak day of the peak month, not the annual average. Tea Board data for 2025 show North India making 13.9% of its annual crop in July alone, about 1.7 times an average month. Sizing a dryer on annual output divided by operating hours can leave it 40% short at peak, which forces leaf to wait or be rushed through. This guide shows a quick capacity check from green leaf to made tea to water evaporated. It is for tea factory owners, estate managers and bought-leaf factories planning new lines or capacity increases.
Moisture figures are on a wet basis. “Made tea” is the finished, dried tea; “dhool” is the fermented leaf entering the dryer.
Why is installed tea factory capacity under review?
The Tea Board is assessing installed factory capacity against green leaf availability. BusinessLine reported on 6 November 2026 that the Board had put revised guidelines for NOCs and registration certificates for new factories and capacity increases on hold, by an order of the same date, until it completes that internal assessment. Coonoor manufacturers had protested the restrictions. The report also cites the industry target of 2,000 million kg of tea by 2030.
We do not know what method the Board will use. Whatever it decides, owners planning expansions will need a clear, defensible statement of what their factory can process at peak. In most CTC and orthodox factories, the dryer is one of the first places to check.
How peaky is Indian tea production?
Very, especially in North India. The table uses the Tea Board’s final 2025 production figures (Tea Board PDF).
| Region (2025) | Annual production | Peak month | Peak share of year | Peak ÷ average month |
|---|---|---|---|---|
| North India | 1,161.30 M kg | July: 161.69 M kg | 13.9% | 1.67 |
| South India | 234.23 M kg | May: 26.57 M kg | 11.3% | 1.36 |
| All India | 1,395.53 M kg | July: 182.54 M kg | 13.1% | 1.57 |
North India makes almost nothing in January and February, then peaks in July to October. South India is flatter. Individual factories can be peakier than the regional figures, because a single flush or a week of good weather is not averaged out.
How do you convert green leaf to dryer load? A worked example
Start from made tea, then work back to dhool and water. A 2024 energy audit of Tripura tea factories by the Citizen consumer and civic Action Group (CAG) gives working figures: about 5 kg of green leaf per kg of made tea, dhool entering the dryer at 50–55% moisture and leaving at 3–4%, and a typical dryer rated at about 100 kg/h of dryer-mouth tea.
Assumptions for a North India factory making 500,000 kg of made tea a year: 300 working days, 20 dryer hours a day, July share 13.9%, and a peak day 30% above the July average. Dhool at 55% moisture, made tea at 3%. All are illustrative; use your own records.
| Basis | Made tea | Working |
|---|---|---|
| Annual average | 83 kg/h | 500,000 ÷ (300 × 20) |
| July average | 112 kg/h | 500,000 × 0.139 ÷ 31 ÷ 20 |
| Peak day | 146 kg/h | 112 × 1.3 |
| Green leaf at peak day | ≈ 730 kg/h | 146 × 5 |
| Dhool to dryer at peak day | ≈ 315 kg/h | 146 × 0.97 ÷ 0.45 |
| Water evaporated at peak day | ≈ 169 kg/h | 315 − 146 |
Sizing on the annual average (83 kg/h) would leave the dryer about 43% below the peak-day load (146 kg/h). With CAG’s typical 100 kg/h unit, this factory needs about one and a half dryers at peak, or one larger dryer. A South India factory of the same size, with May at 11.3% of the year, peaks at about 119 kg/h under the same assumptions.
Why does dhool moisture matter so much?
Because water evaporated, not made tea, sets the heat and air load. GTI’s black tea drying page describes moisture falling from about 60–70% to 2–3%, while the CAG audit measured 50–55% at the dryer inlet. At 146 kg/h of made tea, dhool at 55% means about 169 kg/h of water, but dhool at 65% means about 259 kg/h, over 50% more. Measure dhool moisture during the flush before you size or blame the dryer.
Fuel scales with that water. CAG reports that a typical 100 kg/h dryer burns about 150 kg/h of coal or 250 kg/h of biomass. For water evaporation per kg of made tea and air-flow sizing, see our guide on choosing an industrial tea dryer.
What can you do if the dryer is the bottleneck?
- Confirm it is the dryer. Log leaf intake, withering-trough holding time and dhool waiting time on peak days. If withering or rolling is the limit, a bigger dryer will not help.
- Check the heat supply. A dryer can be limited by its furnace or heat exchanger, not its bed area. Compare the burner or furnace rating with the peak water load.
- Hold the exhaust window. Overloading a dryer drops exhaust temperature and causes stewing; see our CTC tea dryer troubleshooting guide.
- Improve withering. Better-withered leaf reaches the dryer drier and evens out the load.
- Add or replace a dryer. CAG lists fluid bed dryers in place of ECP (endless chain pressure) dryers as an energy-saving measure, quoting 10–15%. Capacity and quality gains need confirming on your own leaf.
Which tea dryer types does GTI publish?
GTI’s tea drying system page lists fluid bed tea dryers and heat pump dryers for black, green, CTC and specialty tea, with a final moisture of about 2–3%. Its vibratory fluid bed dryer page covers the VFBD used for CTC tea. GTI does not publish tea dryer capacities on these pages, so ask for a rating in kg/h of made tea at a stated dhool moisture.
Frequently asked questions
About 5 kg, according to CAG’s 2024 energy audit of Tripura tea factories. The ratio varies with leaf standard, withering and grade, so use your own factory records when sizing equipment.
GTI’s tea drying pages give about 2–3% final moisture, and the CAG audit measured 3–4% for dryer-mouth tea. Agree the exact target with your buyers and packing standard.
No. Size it on peak-day production. Tea Board data for 2025 show North India’s July output at about 1.67 times an average month, and single factories can be peakier than that.
CAG lists replacing ECP dryers with fluid bed dryers as an energy-saving measure, quoting 10–15%. The right choice also depends on tea type, grade mix and quality targets, so confirm on your own leaf.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures fluid bed, vibratory fluid bed and other industrial dryers, including the tea drying systems described on gtidryers.com. On this site, see our drying machines overview. The head office is at 10C Middleton Row, Kolkata 700071, India.
Sources and authorship
- The Hindu BusinessLine, “Tea Board puts revised factory licensing guidelines on hold”, 6 November 2026.
- Tea Board, “Final tea production in 2025 (Jan–Dec)” and 2025–26 (Apr–Mar) tables.
- Citizen consumer and civic Action Group (CAG), “From leaf to cup: A journey through energy-efficient tea processing”, 14 October 2024.
- Published tea drying, black tea and VFBD pages of Genex Tech Industries LLP (GTI Group).
The capacity example is an illustrative calculation from stated assumptions, not a measurement from any factory or an interpretation of Tea Board licensing rules. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named engineer, and no individual is cited as having approved the technical content.
Next step
Checking whether your tea dryer can handle the peak flush? Email mktg@gtidryers.com or use the contact page. Send your tea type (CTC, orthodox or green), peak-day green leaf intake, dhool and made tea moisture, current dryer type and rating, fuel and the factory location.
