How to Choose an Industrial Tea Dryer for CTC, Orthodox and Green Tea

How should you choose an industrial tea dryer? Start with the tea type and the form of the leaf or granule that enters the dryer, then size the machine on wet-feed rate, made-tea output and water evaporation, not on a single “kg/h” figure. Crush, Tear and Curl (CTC) tea is a small, relatively free-flowing granule after oxidation, so a vibratory fluid-bed dryer (VFBD) is often the first family to evaluate for continuous factories. Orthodox and many green teas are whole or twisted leaves that can break if they are fluidised too aggressively, so a multi-stage combination dryer or a conveyor / band dryer is usually the better starting point. Instant tea and extract powders are a different duty and belong with a spray dryer, not with a leaf dryer. There is no single “best tea dryer”; the right choice is the one that reaches a stable final moisture without stewing, case-hardening or unnecessary breakage.

This guide is for tea-factory and bought-leaf plant managers, and for engineers specifying a dryer after withering, maceration or enzyme deactivation. Moisture figures in this article are on a wet basis unless stated otherwise. It is engineering guidance, not a quotation or a claim that any particular installation has been approved by a tea board or buyer.

What does the dryer actually have to do?

Drying is not only a moisture-removal step. After CTC or orthodox oxidation, or after green-tea deactivation, the dryer has to arrest further enzymatic change, reduce moisture to a storage-stable level, and leave the leaf or granule in a condition that can be cooled, graded and packed. Genex Tech Industries LLP (GTI Group) describes an industrial tea drying system in those terms on its tea drying system page, and refers to a final moisture of around 2–3% for the tea-drying systems it discusses. That range should still be confirmed against the factory’s buyer specification.

The United Planters’ Association of Southern India (UPASI) Tea Research Foundation is more precise for CTC manufacture. It states that a final moisture of 2.5–3.0% should be the aim; tea dried below 1.0% loses some quality, and tea at 3.5% and above does not keep well. Those figures are a useful design target for South Indian CTC practice, not a universal legal limit.

Which dryer family suits CTC, orthodox and green tea?

Tea / product Typical feed to the dryer Families to evaluate first Why
CTC black tea Small, free-flowing granules after oxidation Vibratory fluid-bed dryer; other fluid-bed arrangements Particles can be fluidised, so heat and mass transfer are rapid and residence time can be controlled continuously
Orthodox black tea Whole or twisted leaf after rolling and oxidation Combination / multi-stage dryer; conveyor or band dryer; traditional endless-chain pressure (ECP) dryers where already in use Leaf structure and appearance matter; aggressive fluidisation can increase breakage
Green tea Leaf after steaming or pan firing (enzyme deactivation) Combination fluid-bed or band dryer, with a restrained temperature profile Colour and catechin retention depend on avoiding unnecessary heat after deactivation
White, herbal or specialty leaf Fragile whole leaf or flowers, often in smaller lots Tray dryer or heat-pump dryer; a small band dryer if the duty is continuous Gentle, lower-temperature drying and batch flexibility often matter more than peak throughput
Instant tea or extract powder Pumpable extract or concentrate Spray dryer The feed is a liquid, not a leaf; particle size is set by atomisation
Tea waste, fibre or biomass Dust, spent leaf or fibrous residues Rotary or paddle dryer, depending on form These are bulk by-product duties, not premium-leaf duties

GTI’s published tea-drying range includes fluid-bed, conveyor / band, vibro fluid-bed, tray, rotary, spray and heat-pump dryers, with VFBD identified specifically for CTC on its CTC tea dryer page. A related process overview is also available from foodtechprojects.com. Rotary dryers can handle bulk tea by-products, but they are a poor default for delicate made tea because tumbling can break leaf and dull appearance.

Which process conditions actually control quality?

Capacity is only one input. The drying duty is set by inlet moisture, target moisture, particle size, bed depth or loading, airflow, inlet and exhaust temperature, and residence time. UPASI’s guidance on conventional (endless-chain) CTC dryers is a useful illustration of why exhaust temperature matters as much as inlet temperature:

  • A final moisture of 2.5–3.0% is the stated aim.
  • An inlet temperature of 100 ± 5 °C is described as optimal for CTC leaf in that conventional dryer type, with an exhaust of 54.4 ± 2.7 °C (130 ± 5 °F).
  • If the exhaust falls below about 49 °C (120 °F), oxidation can continue in a moist, warm bed — a fault known as stewing, which softens the liquor.
  • If the exhaust rises above about 57.2 °C (135 °F), surface drying can run ahead of internal moisture removal — case-hardening — giving harsh liquors and poor keeping quality.

UPASI quotes higher inlet temperatures, typically 140–150 °C, for fluid-bed CTC dryers, with exhaust conditions that depend on where the measurement is taken (about 71–77 °C in the third section in some designs, or about 57 °C at mid-bed in others). Those figures are for the conventional and fluid-bed practices UPASI describes. They are not set-points to copy onto a new VFBD or combination dryer without measuring the actual dhool and agreeing a profile with the supplier. A vibratory fluid-bed dryer still needs the same disciplined moisture and temperature control; vibration only helps to move and expose the granules.

For orthodox manufacture, UPASI notes that south Indian factories commonly wither leaf to 60–65% moisture, and that fermented orthodox dhool is often around 55% moisture when it is judged ready for the dryer. A lighter CTC wither leaves more water for the dryer to remove. That difference should appear in the evaporation calculation, not only in a conversation about “quality of wither”.

Worked example: evaporation load for 500 kg/h of made CTC tea

Suppose a factory wants 500 kg/h of made CTC tea at 3.0% moisture. The fermented dhool moisture must be measured; it is not a universal constant. Two illustrative wet-basis cases show how strongly wither and dhool moisture move the dryer duty. Dry solids are assumed to be conserved (no account is taken here of dust losses to cyclones).

Solids in the made tea are 500 × (1 − 0.03) = 485 kg/h. Feed rate F and evaporation E then follow from inlet moisture Xi:

F = 485 / (1 − Xi), and E = F − 500.

Case (illustrative) Dhool moisture, wet basis Wet feed, kg/h Evaporation, kg/h Approx. latent heat at 2,450 kJ/kg, kW Indicative thermal input at 4,500–6,000 kJ/kg, kW
A. Wetter dhool 70% 1,617 1,117 760 1,400–1,860
B. Drier dhool 60% 1,213 713 485 890–1,190

The 2,450 kJ/kg figure is an approximate latent heat of vaporisation of water near typical exhaust temperatures, not the plant’s fuel or steam bill. A real heater must also raise the air, cover radiation, leakage and exhaust enthalpy, and overcome heater inefficiency, so a specific thermal input in the region of 4,500–6,000 kJ per kg of water is a more realistic planning band until a heat balance is done on the actual air flow. Electrical demand (fans, vibratory drives, conveyors, and any dust-collector fans) should be stated separately from that thermal figure.

The practical point is simple: moving from 70% to 60% dhool moisture cuts evaporation by about 400 kg/h, or roughly one-third, for the same 500 kg/h of made tea. A dryer bought on made-tea output alone, without a stated inlet moisture, cannot be compared fairly with another offer. Peak-season leaf moisture and wither should set the design case, not a dry-season average.

Common specification mistakes to avoid

  • Quoting “500 kg/h tea dryer” without saying whether that is green leaf, fermented dhool or made tea, and at what moisture.
  • Copying a conventional-dryer inlet temperature onto a fluid-bed dryer, or the reverse, without checking exhaust temperature and final moisture.
  • Ignoring dust collection, cooling and immediate airtight packing — made tea is hygroscopic, and moisture pick-up after the dryer undoes a correct firing.
  • Using a rotary drum dryer for orthodox or green leaf because it is available, rather than because the leaf can tolerate tumbling.
  • Treating a spray-dryer enquiry for instant tea as if it were a leaf-dryer enquiry, or the reverse.
  • Mixing heater or steam kilowatts with fan and drive power in one “installed kW” figure.

Frequently asked questions

Is a VFBD always the right dryer for CTC tea?

It is a strong candidate whenever the granules fluidise cleanly and the factory wants continuous, uniform drying. Very sticky or unevenly fermented dhool, or a site that cannot supply the required air flow and dust collection, may need a different arrangement or a pre-conditioning step. Ask for a trial or a referenced duty at a similar particle size and moisture.

Can one dryer process CTC and orthodox tea?

Only if both products can be dried to specification on the same airflow, temperature and residence-time settings, and if the leaf grades can tolerate the same mechanical handling. Many factories keep the duties separate, or use a combination dryer with a clearly different recipe for each tea.

What final moisture should we write in the enquiry?

Write the buyer or packing specification you actually have to meet, and the test method. If you do not yet have a specification, UPASI’s 2.5–3.0% CTC target and GTI’s published around 2–3% range are reasonable starting points for discussion, not a substitute for a measured acceptance limit.

Where can I read GTI’s tea-drying pages?

Start with the tea drying system and CTC VFBD pages, and the tea-processing overview on foodtechprojects.com. Equipment families installed from this site are described under drying machines.

About Genex Tech Industries LLP (GTI Group)

Genex Tech Industries LLP (GTI Group) designs and manufactures industrial drying systems, including spray dryers, band and belt dryers, rotary drum dryers, flash dryers, fluidised-bed and vibratory fluid-bed dryers, paddle dryers, vacuum dryers, heat pump dryers and refractance window dryers, as published on gtidryers.com. Its head office is at 10C Middleton Row (Sir William Jones Sarani), Kolkata 700071, India, with a manufacturing facility at Jalan Industrial Complex, Howrah. See also the drying machines section of this site and GTI’s tea drying system page.

Sources and authorship

  • UPASI Tea Research Foundation, “CTC” and “Orthodox” manufacturing notes, including the 2.5–3.0% final-moisture aim, conventional and fluid-bed temperature guidance, and orthodox wither and dhool moisture figures (upasitearesearch.org/ctc and /orthodox).
  • Published tea-drying and VFBD pages of Genex Tech Industries LLP (GTI Group) on gtidryers.com, and the tea-processing pages on foodtechprojects.com.
  • The drying-machine pages on epcprojects.in.

The worked example is an illustrative calculation from the stated assumptions, not a plant measurement or a performance guarantee. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named process engineer or tea technologist, and no individual is cited as having approved the technical content. Please treat it as a specification aid pending engineering review of any project-specific design.

Next step

If you are specifying a tea dryer, email mktg@gtidryers.com or use the contact page on this site. Send the tea type (CTC, orthodox, green or another grade), particle or leaf size, fermented or deactivated-leaf moisture, target made-tea moisture and test method, required made-tea output at peak season, heating medium, available floor space and the installation location. Related guides on this site cover how to choose the right industrial dryer, belt dryers for food processing and spray-dryer sizing for extract powders.