Does biochar feedstock need drying before pyrolysis, and how much does it matter? Usually yes. ICAR-CICR’s 2026 bulletin says biomass above 30% moisture must be dried before pyrolysis, because water lowers thermal efficiency and biochar quality. Continuous reactors often need drier feed than that; take the inlet limit from your reactor supplier. Drying 50 t/day of cotton stalks from 35% to 12% removes about 13 t of water a day. Where that heat comes from also matters: drying with fossil fuel adds emissions that carbon-removal methodologies deduct. This guide is for biochar project developers, cement and power companies co-locating pyrolysis units, and agro-residue aggregators.
All moisture figures are on a wet basis (water as a percentage of total mass).
Why are biochar plants being planned in India now?
Developers are announcing industrial-scale pyrolysis units for crop residues, mainly to sell carbon-removal credits on voluntary markets and to supply syngas to industry. The items below are announcements and plans reported by the companies or press, not verified operating results.
- The Hindu (23 January 2026) reported a 10-year agreement between Sow & Reap Chara and Sagar Cements for biochar and gasification units at Mattampally, Telangana. According to the company, each unit would process 15,000 t of biomass a year into 3,750 t of biochar, with syngas used as kiln fuel.
- A Green Carbon Inc. press release (24 February 2026) announced 50 TPD pyrolysis plants with Excellent Enfab in Gujarat and West Bengal, using flower stems, peanut shells and bamboo, targeting Isometric certification.
- India’s compliance carbon market does not yet cover biochar. BEE’s list of approved Offset Mechanism methodologies (updated 7 July 2026) has 12 methodologies, none for biochar. Projects are therefore using voluntary standards such as Verra VM0044 v1.2, active since 27 June 2025.
What moisture should biochar feedstock reach before the reactor?
Low enough for the reactor to run on its own pyrolysis gas, and steady enough to hold char quality. CICR sets 30% as the point above which drying is mandatory. GTI’s biomass drying page quotes typical biomass at 30–60% moisture and dried targets of 8–15% for fuel and pellet uses.
Moisture that enters the reactor must be evaporated there and heated to pyrolysis temperature. CICR’s bulletin describes pyrolysis at 300–700 °C. That heat comes out of the pyrolysis gas. If the feed is too wet, the reactor cools, may need extra fuel, and produces more aqueous condensate. Just as important is consistency: a feed that swings between 10% and 30% makes temperature control, and therefore carbon stability, harder.
How much drying does a 50 TPD plant need? A worked example
For 50 t/day of chopped cotton stalks arriving at 35% and dried to 12%, the dryer removes about 13 t of water a day, or 545 kg/h over 24 hours. At an assumed 3.5 MJ per kg of water, that needs about 0.53 MW of heat.
| Item | Value | Working |
|---|---|---|
| Dry matter | 32.5 t/day | 50 × (1 − 0.35) |
| Dried feed to reactor at 12% | 36.9 t/day | 32.5 ÷ 0.88 |
| Water evaporated | 13.1 t/day (≈ 545 kg/h) | 50 − 36.9 |
| Dryer heat at 3.5 MJ/kg water | ≈ 46 GJ/day (≈ 0.53 MW) | 13,070 × 3.5 MJ |
| Biochar output | ≈ 6.6–15.1 t/day | 20.4–46.5% recovery from dry stalks at 350–400 °C (CICR) |
| Drying heat per tonne of biochar | ≈ 3.0–6.9 GJ/t | 46 GJ ÷ biochar output |
The 35% arrival moisture, 3.5 MJ/kg and 24-hour operation are illustrative assumptions. Note that “50 TPD” in announcements may mean feed or product, and wet or dry. Fix that in the contract.
Why does the dryer’s heat source affect carbon credits?
Removal methodologies credit net removals: the carbon stored in biochar minus project emissions such as fossil energy used in production. If the 46 GJ/day in the example came from coal at the IPCC 2006 default of about 94.6 kg CO₂ per GJ, it would emit roughly 4.3 t CO₂ a day. That is roughly 0.3–0.7 t CO₂ per tonne of biochar.
For scale, the Telangana announcement implies about 2.1 t CO₂ mitigated per tonne of biochar (8,000 t ÷ 3,750 t). That is a press figure, not a verified credit, but it shows that a fossil-fired dryer could consume a meaningful share of the claim. The usual answer is to dry with heat recovered from burning the pyrolysis gas, or with other waste heat, and to meter it. Check how your chosen standard treats drying energy before you fix the design.
Which dryer suits biochar feedstock?
It depends on particle form, the temperature of available waste heat and capacity. All three types below appear on GTI’s biomass drying pages.
| Dryer | Fits | Watch-outs |
|---|---|---|
| Rotary drum dryer | Chopped stalks, shells, chips; high tonnage; can use hot flue gas from gas combustion | Fire risk with dry fines; control exhaust temperature and oxygen |
| Belt / mesh belt dryer | Light residues such as straw and husk; can use lower-temperature waste heat | Needs even bed loading; larger footprint |
| Flash dryer | Sawdust and fine milled biomass | Needs fine, uniform feed; large dust collection |
See GTI’s rotary drum dryer and biomass fuel drying pages. Feed must be chopped to a uniform size before drying; that helps both the dryer and the reactor.
What should a biochar feedstock dryer specification include?
- Feedstock types and seasons, with arrival moisture ranges measured on your own material, not literature values.
- Reactor inlet moisture limit and allowed variation, signed off by the reactor supplier.
- Wet feed rate, water evaporation rate and dried output stated separately, in kg/h.
- Heat source: flue gas temperature and flow from the pyrolysis-gas combustor, and any backup fuel.
- Fire and explosion protection: spark detection, temperature monitoring and venting; see our dust explosion protection checklist.
- Metering of dryer fuel and power, so the carbon accounting can use measured data.
Frequently asked questions
ICAR-CICR’s 2026 bulletin says biomass above 30% moisture must be dried before pyrolysis. Continuous reactors usually need lower and steadier moisture than that, so take the exact inlet limit from your reactor supplier.
Often, yes. The pyrolysis gas can be burned and the flue gas or recovered heat used in the dryer. Whether it is enough depends on feed moisture, gas yield and the reactor’s own heat demand, so check it with a heat balance.
Not yet. BEE’s list of approved Offset Mechanism methodologies, updated 7 July 2026, contains no biochar methodology. Biochar projects currently use voluntary standards such as Verra VM0044.
Yes. Dry fines, hot gas and sparks can ignite in dryers, cyclones and ducts. Fit temperature monitoring, spark detection and suppression, and keep the dryer and ducting clean.
About Genex Tech Industries LLP (GTI Group)
Genex Tech Industries LLP (GTI Group) designs and manufactures rotary, belt and flash dryers, including the biomass drying systems described on gtidryers.com. On this site, see our rotary dryer and belt dryer pages, and our guide on sizing a biomass pellet dryer for co-firing. The head office is at 10C Middleton Row, Kolkata 700071, India.
Sources and authorship
- ICAR-Central Institute for Cotton Research, “Biochar Production from Cotton Stalks”, Technical Bulletin 2026/1.
- The Hindu, “Climate-tech firm, cement maker ink pact for integrated biochar, gasification units”, 23 January 2026.
- Green Carbon Inc., press release on partnership with Excellent Enfab Incorporation, 24 February 2026.
- Bureau of Energy Efficiency, “Methodologies and Tools under Offset Mechanism”, last updated 7 July 2026.
- Verra, VM0044 Biochar Utilization in Soil and Non-Soil Applications, v1.2.
- IPCC, 2006 Guidelines for National Greenhouse Gas Inventories, Vol. 2, Ch. 1 (default CO₂ emission factors).
- Published biomass drying, biomass fuel drying and rotary dryer pages of Genex Tech Industries LLP (GTI Group).
The plant example and emission estimate are illustrative calculations from stated assumptions, not measurements, quotations or credit calculations for any project. This article was prepared by the editorial team of Genex Tech Industries LLP (GTI Group) with AI editorial assistance. It has not been reviewed by a named engineer, and no individual is cited as having approved the technical content.
Next step
Planning feedstock drying for a pyrolysis or biochar plant? Email mktg@gtidryers.com or use the contact page. Send the feedstock types, arrival moisture range, reactor inlet limit, feed rate in t/day, available waste heat (temperature and flow) and the installation location.

